GBC AdvancedPunch Pro - 6. General Procedures and Information

GBC AdvancedPunch Pro 09/11/2018 General Procedures and Information
6-1 Section Contents
6. General Procedures and Information
Section Contents
Title Page
General Procedures ................................................................... 6-3
User Interface ............................................................................ 6-3
Settings .................................................................................. 6-4
Information ............................................................................. 6-4
User Interface Screen Map ................................................... 6-5
DFA configuration only- User Interface Screen Map ............. 6-6
GP 6.1 User Interface Procedure ................................... 6-7
GP 6.1.1 BACKGAGE MODE Procedure ......................... 6-7
GP 6.1.2 PUNCH MODE Procedure- for DFA configurations only
......................................................................... 6-10
GP 6.1.3 ALIGNMENT MODE Procedure ...................... 6-12
GP 6.1.4 TAB/COVER MODE Procedure ....................... 6-14
GP 6.1.5 CLEAR COVER Procedure ............................. 6-16
GP 6.1.6 LANGUAGE MODE Procedure ....................... 6-18
GP 6.1.7 UNITS MODE Procedure ................................. 6-19
GP 6.1.8 PAPER SIZE Procedure .................................. 6-20
GP 6.1.9 DIE TYPE Procedure ....................................... 6-21
GP 6.1.10 DIE CYCLES Procedure .................................. 6-22
GP 6.1.11 PUNCH CYCLES Procedure ........................... 6-23
GP 6.1.12 FIRMWARE Procedure .................................... 6-24
Service User Interface ............................................................. 6-25
Service Interface Screen Map ............................................. 6-27
DFA Configurations only- Service Interface Screen Map.... 6-28
GP 6.2 Service User Interface Procedure .................... 6-29
GP 6.2.1 SPEED ADJUST Procedure ............................ 6-30
GP 6.2.2 SPEED (DFA) Procedure- for DFA configurations only
......................................................................... 6-31
GP 6.2.3 PAPER SIZE Procedure .................................. 6-32
GP 6.2.4 MAX BYPASS Setting...................................... 6-33
GP 6.2.5 RUN MODE Setting ......................................... 6-34
GP 6.2.6 DIE CYCLES .................................................... 6-35
GP 6.2.7 SENSORS Procedure ...................................... 6-36
GP 6.2.8 I/O SIGNALS Procedure .................................. 6-38
GP 6.2.9 DFA STATUS Procedure- DFA Configurations only
......................................................................... 6-39
GP 6.2.10 SOLENOIDS Procedure .................................. 6-40
GP 6.2.11 MOTORS Procedure ........................................ 6-41
GP 6.2.12 FUNCTION TESTS Procedure (Cycle Punch, Aligner
Test, Fan Test) ................................................. 6-42
GP 6.2.13 SKEW OFFSETS Procedure ........................... 6-44
GP 6.2.14 ALIGN OFFSETS Procedure ........................... 6-48
GP 6.2.15 LOG .................................................................. 6-50
GP 6.2.16 FIRMWARE UPGRADE Procedure ................. 6-51
GP 6.3 Undock the Punch (Moving the punch to Service position)
......................................................................... 6-53
GP 6.4 Dock the punch (Moving the punch to Operating position)
......................................................................... 6-54
GP 6.5 Operational Inspection ..................................... 6-55
GP 6.6 Internal Inspection ............................................ 6-55
GP 6.7 Die Set Service ................................................ 6-56
GP 6.7.1 Die Set Life Expectancy ................................... 6-56
GP 6.7.2 Die Set Components ........................................ 6-56
GP 6.7.3 Die Set Lubrication ........................................... 6-57
GP 6.7.4 Die Set Shoulder Bolts ..................................... 6-58
GP 6.8 External Cleaning ............................................. 6-59
GP 6.9 Internal Cleaning .............................................. 6-59
GP 6.10 Base Cleaning .................................................. 6-60
GP 6.11 Chip Bin Cleaning ............................................ 6-60
GP 6.12 Die Guide Cleaning .......................................... 6-61
GP 6.13 Door Latch Inspection ...................................... 6-61
GP 6.14 Idler Roller and Idler Springs Inspection .......... 6-62
GP 6.14.1 Idler Roller Cleaning ......................................... 6-63
GP 6.14.2 Steering Idler Roller and Springs Inspection and Cleaning
......................................................................... 6-64
GP 6.15 Drive Roller and Steering Drive Roller Inspection and
Cleaning ........................................................... 6-65
GP 6.16 Panel Latch Inspection ..................................... 6-66
GP 6.17 Optical Sensor Cleaning .................................. 6-69
GP 6.18 Bypass Paper Path Inspection and Cleaning... 6-70
GP 6.19 Punch Paper Path Inspection and Cleaning .... 6-71
GP 6.20 Punch Drive Cam Lubrication .......................... 6-72