Phaser 6300/6350/6360 Color Laser Printer Service Manual I – 9
test print, 5-5
600 x 600 test print, 5-9
analyzing, 5-8
CMYK test print, 5-5
engine test print, 5-10
Service Diagnostics test prints, A-14
service test print, 5-9
setting test parameters, A-15
Test Print Button, 5-10
location, 1-7
operation, 5-10
Thermistor, 2-18
Toner
density control
, 2-11
life count, 1-12
metered, 1-4
presence detect, 2-14
transport, 2-44
Toner Cartridge, 2-43
failure error, 3-8
metered cartridges, 1-4
part number, 9-60
presence detect, 2-14
removal, 8-8
remove ribbon error, 3-7
validation, 6-9
view life count, 6-9
Toner Cartridge Assembly, 2-43
Toner Cartridge Holder, 2-43
components, 2-43
part number, 9-31
removal, 8-86
Toner Cartridge In Sensor, 2-43
actuator part number, 9-31
bracket part number, 9-31
removal, 8-90
Toner Full Sensor, 2-32
connector location, 10-6
location, 2-21
part number, 9-21
removal, 8-73
testing, A-18
wiring, 10-24
Toner Motor, 2-44
connector location, 10-5
drive train, 2-44
location, 2-43
precautions, A-16
testing, A-16
wiring, 10-21
Transfer Roller, 2-36
install or reseat error, 3-7
life count, 1-12
life count reset, 6-9
location, 1-10
part number, 9-19
presence detect, 2-13
removal, 8-7
replace transfer roller error, 3-6
Toner Full Sensor, 2-13
waste toner reservoir, 2-5
status, 2-13
Tray, 2-39
capacity, 1-19
components, 2-39
Feed Roller
removal
, 8-35
replacement kit, 9-61
Feeder Chute
part number
, 9-9
guides, 2-39
insert Tray 2~5 error, 3-7
Label Kit, 9-59
Low Paper Sensor
connector location
, 10-8
part number, 9-13
removal, 8-32
testing, A-17
misfeed (jam T2~5) error, 3-6
No Paper Sensor
part number
, 9-13
removal, 8-31
numbering, 2-7
optional trays, 1-9
out of paper, load tray 2~5 error, 3-7
paper handling, 6-5
paper is low error, 3-8
paper not available, load tray 2~5 error, 3-7
Paper Pick Assembly
part number
, 9-13
part number, 9-7
Rear Cover
part number
, 9-9
removal, 8-23
Retard Roller
part number
, 9-7
removal, 8-21
tray missing warning, 3-8
wrong paper size, load tray 2~5 error, 3-7
Tray 1 (MPT), 8-43
components, 2-38
Envelope Feed Rollers, 2-38
Feed Roller, 2-38
part number, 9-23
removal, 8-51
Feed Solenoid, 2-38
connector location, 10-5
location, 2-33
part number, 9-23
removal, 8-44
wiring, 10-26
misfeed (jam T1) error, 3-6
No Paper Sensor, 2-38
connector location, 10-5
part number, 9-23
removal, 8-47
testing, A-17
wiring, 10-26
operation, 2-38
out of paper, load tray error, 3-7
paper handling, 6-5
paper not available, load tray error, 3-7
Retard Roller, 2-30
part number, 9-15
To Next Page
Loading...
