Hioki 8841 - Page 408

494 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

384

────────────────────────────────────────────────────

17.2 Using the Key Lock Function

────────────────────────────────────────────────────

Table of Contents

Default Chapter3
- Table of Contents3
Safety Notes17
Notes on Use19
Chapter Summary23
Chapter 1 Product Overview25
- Major Features25
- Identification of Controls and Indicators27
Chapter 2 Installation and Preparation31
- Installation of the Unit31
- Power Supply and Ground Connections33
- Power On/Off37
- Connection of the Input Unit38
- Logic Probe Connection44
- 9018-10/9132-10 Clamp on Probe45
- 9322 DIFFERENTIAL PROBE Connection46
- Loading Recoding Paper47
- Care of Recording Paper49
- Notes on Measurement50
  - Maximum Input Voltage52
  - Using a Voltage Transformer53
Chapter 3 Basic Key Operation55
- Basic Key Operation55
- Other Keys Operation58
- Screen Configuration59
Chapter 4 Memory Recorder Function61
- Overview of the Memory Recorder Function61
- Operation Sequence (MEM)63
- STATUS Settings (MEM)65
- Using the X-Y Waveform Plots (MEM)78
- Settings on the Waveform Display Screen (MEM)81
- Auto Range Function82
- Other Screen Settings84
- Start and Stop Operation (MEM)85
Chapter 5 Recorder Function87
- Overview of the Recorder Function87
- Operation Sequence (REC)89
- STATUS Settings (REC)91
- Settings on the Waveform Display Screen (REC)105
- Start and Stop Operation (REC)106
Chapter 6 RMS Recorder Function107
- Overview of the RMS Recorder Function107
- Operation Sequence (RMS)108
- STATUS Settings (RMS)110
- Settings on the Waveform Display Screen (RMS)119
- Start and Stop Operation (RMS)120
Chapter 7 Recorder & Memory Function121
- Overview of the Recorder & Memory Function121
- Operation Sequence (REC&MEM)122
- STATUS Settings (REC&MEM)124
- Start and Stop Operation (REC&MEM)142
Chapter 8 FFT Function143
- Overview of the FFT Function143
- Operation Sequence (FFT)144
- STATUS1 Settings (FFT)146
- STATUS2 Settings (FFT)159
- Settings on the Waveform Display Screen (FFT)167
- Start and Stop Operation (FFT)168
- FFT Analysis Function169
Chapter 9 Input Channel Settings189
- Overview189
- Operation Procedure (Input Channel Setting)190
- Setting the CHANNEL Screen192
- Copying Channel Settings199
- Zero Settings200
  - Zero Adjustment200
  - Zero Offset Setup201
- Channel Guide Function203
- Setting the Variable Function204
- Scaling Function (SYSTEM2)206
  - Setting the Scaling Function207
  - Scaling Setting Example210
- Comment Function (SYSTEM 3)211
- Setting the Waveform Display Screen215
- Setting the 8937 VOLTAGE/TEMP UNIT218
  - Making the Settings of Voltage Measurement218
  - Making the Settings of Temperature Measurement220
- 8938 Fft Analog Unit223
- Setting the 8939 STRAIN UNIT224
- 8940 F/V Unit225
- Setting the 8947 CHARGE UNIT236
Chapter 10 Trigger Functions241
- Overview of the Trigger Functions241
- Operation Sequence (Trigger Mode Setting)242
- TRIGGER Screen Organization244
- Trigger Mode245
- Pre-Trigger246
- Trigger Timing (REC Only)248
- Trigger Source AND/OR Linking249
- Analog Trigger250
- Logic Trigger262
- External Trigger Function264
- Timer Trigger Function265
- Manual Trigger268
- Trigger Output Terminal268
Chapter 11Waveform Display Screen Operation269
- Scrolling the Waveform270
- Using the A･B Cursors271
- Magnification/Compression Ratio Along the Time Axis277
- Zoom Function (MEM Only)278
- Input Level Monitor Function279
- View Function (VIEW Key)280
  - Position Display280
  - Block Display (MEM Only)281
Chapter 12 SYSTEM Screen Settings283
- Overview283
- SET up Screen (SYSTEM 1)284
- SCALING Screen (SYSTEM 2)290
- COMMENT Screen (SYSTEM 3)291
- INTERFACE Screen (SYSTEM 4)292
- INITIALIZE Screen302
- Self-Check304
Chapter 13 Printout of Measurement Data307
- Printout of Measurement Data Operating Procedure308
- Setting the STATUS Screen (Printout)310
  - Setting the Display Format310
  - Setting the Print Mode311
- Setting the CHANNEL Screen (Printout)312
  - Setting the Print Density312
  - Setting the Waveform Display Graph Position313
- Setting the SYSTEM Screen (Printout)314
- Example of Printer Output320
- Printing Procedure327
- External Printer (Color Print)332
Chapter 14 Storing Measurement Data335
- Floppy Disk336
- 9607 MO UNIT (Option)337
  - Setting the Internal MO338
- PC Card339
  - Using the PC Card Slot (PC Card with a Cable Only)340
- SCSI Interface341
- Initializing (FORMAT)345
- Saving the Data (SAVE)346
- Setting the Data to Store348
- Loading the Data (LOAD)355
- File Information (INFO)359
- Deleting the Data (DELETE)360
- Sorting Files (SORT)361
- Operating the Directory362
- Printing the File List365
Chapter 15 Memory Segmentation Function367
- Using the Sequential Save Function368
- Using the Multi-Block Function (MEM)373
Chapter 16 Waveform Operation Function377
- Waveform Parameter Calculation (MEM)377
- Calculating Waveform Data385
- Waveform GO/NG Evaluation (MEM, FFT)396
- Setting the Waveform Area398
- Setting the Waveform Evaluation Mode399
- Setting the GO/NG Stop Mode399
- Creating the Evaluation Area400
  - Editor Command Details400
  - Function400
Chapter 17 External Input/ Output Terminals/ Key Lock403
- External Input/Output Terminals403
- Using the Key Lock Function407
Chapter 18 Specifications409
- General Specifications409
- External Data Storage and Interface411
- Trigger Unit413
- Memory Recorder Function414
- Recorder Function415
- RMS Recorder Function416
- Recorder & Memory Function417
- FFT Function418
- Auxiliary Functions419
- Others420
- System Operation421
- Maximum Recording Length for Time Axis Settings422
- Memory Capacity and Recording Length424
Chapter 19 Logic and Analog Inputs425
- Logic Inputs425
- Analog Inputs427

Related product manuals

Preview: Hioki 8835-01

Preview: Hioki SM-8213

Preview: Hioki 8730-10

Preview: Hioki 3390

Preview: Hioki IM3523

Preview: Hioki PW3390

Preview: Hioki PW3198

Preview: Hioki RM3545

Preview: Hioki 3280-10F

Preview: Hioki BT3562-01

Hioki BT3562-01