Cisco MDS 9000 Series Command Reference

Send documentation comments to mdsfeedback-doc@cisco.com
21-42
Cisco MDS 9000 Family Command Reference
OL-8413-07, Cisco MDS SAN-OS Release 3.x
Chapter 21 S Commands
source
source
To configure a switched port analyzer (SPAN) source, use the source command in SPAN session
configuration submode. To disable this feature, use the no form of the command.
source {
filter vsan vsan-id |
interface {
fc slot/port [rx [traffic-type {initiator | mgmt | target}] | tx [traffic-type {initiator | mgmt |
target}] | traffic-type {initiator | mgmt | target}] |
fcip fcip-id |
fv slot/dpp-number/fv-port |
iscsi slot/port [rx [traffic-type {initiator | mgmt | target}] | tx [traffic-type {initiator | mgmt
| target}] | traffic-type {initiator | mgmt | target}]|
port-channel channel-number [rx [traffic-type {initiator | mgmt
| target}] | tx [traffic-type
{initiator | mgmt | target}] | traffic-type {initiator | mgmt | target}] |
sup-fc number [rx [traffic-type {initiator | mgmt | target}] | tx [traffic-type {initiator |
mgmt | target}] | traffic-type {initiator | mgmt | target}]} |
vsan vsan-id}
no source {
filter vsan vsan-id |
interface {
fc slot/port [rx [traffic-type {initiator | mgmt | target}] | tx [traffic-type {initiator | mgmt |
target}] | traffic-type {initiator | mgmt | target}] |
fcip
fcip-id |
fv slot/dpp-number/fv-port |
iscsi slot/port [rx [traffic-type {initiator | mgmt | target}] | tx [traffic-type {initiator | mgmt
| target}] | traffic-type {initiator | mgmt | target}]|
port-channel channel-number [rx [traffic-type {initiator | mgmt | target}] | tx [traffic-type
{initiator | mgmt | target}] | traffic-type {initiator | mgmt | target}] |
sup-fc number [rx [traffic-type {initiator | mgmt | target}] | tx [traffic-type {initiator |
mgmt | target}] | traffic-type {initiator
| mgmt | target}]} |
vsan vsan-id}
Note On a Cisco Fabric Switch for HP c-Class BladeSystem and on a Cisco Fabric Switch for IBM
BladeCenter, the syntax differs as follows:
interface {bay port | ext port}
Syntax Description filter Configures SPAN session filter.
vsan vsan-id Specifies the VSAN ID. The range is 1 to 4093.
interface Specifies the interface type.
fc slot/port (Optional) Specifies the Fibre Channel interface ID at a slot and port on an
MDS 9000 Family switch.
fcip fcip-id Specifies the FCIP interface ID. The range is 1 to 255.
fv
slot/dpp-number/fv-port
Specifies a virtual F port (FV port) interface in the specified slot along with
the data path processor (DPP) number and the FV port number.

Cisco MDS 9000 Series Specifications

General

Category	Switch
Operating System	Cisco NX-OS
Ports	Varies by model
Protocols	Fibre Channel (FC), Fibre Channel over IP (FCIP), iSCSI
Redundancy	Redundant supervisors, power supplies, and fans
Management	Cisco Data Center Network Manager (DCNM), CLI, SNMP
Virtualization Support	VSANs (Virtual SANs)
Security Features	Fibre Channel Security Protocol (FC-SP)
Hot Swappable Components	power supplies, fans
Power Supply Options	AC and DC options available