Cisco MDS 9000 Series Command Reference

Send documentation comments to mdsfeedback-doc@cisco.com
22-242
Cisco MDS 9000 Family Command Reference
OL-8413-07, Cisco MDS SAN-OS Release 3.x
Chapter 22 Show Commands
show module
4 powered-dn Insufficient resources (dest Index)
Mod Sw Hw World-Wide-Name(s) (WWN)
--- ----------- ------ --------------------------------------------------
3 3.0(0.322) 0.222 20:81:00:05:30:01:9c:02 to 20:8c:00:05:30:01:9c:02
switch# show port index-allocation
Module index distribution:
------------------------------------------------------+
Slot | Allowed | Alloted indices info |
| range | Total | Index values |
-----|---------|-------|------------------------------|
1 | ----- | - | (None) |
2 | ----- | - | (None) |
3 | 0- 255| 12 | 219-230 |
4 | ----- | - | (None) |
5 | 0- 255| 48 | 0-13,74-79,96-123 |
6 | 0- 255| 48 | 124-150,232-252 |
9 | 0- 255| 24 | 154-177 |
10 | ----- | - | (None) |
11 | 0- 255| 4 | 151-153,231 |
12 | 0- 255| 48 | 32-73,178-183 |
13 | 0- 255| 16 | 80-95 |
SUP | 253-255 | 3 | 253-255 |
switch# show module 4 recovery-steps
Failure Reason:
Contiguous and aligned indices unavailable for Generation-1 modules
Check "show port index-allocation" for more details
Please follow the steps below:
1. Power-off module in one of the following slots: 12
2. Power-on module in slot 4 and wait till it comes online
3. Power-on the module powered-off in step 1
4. Do "copy running-config startup-config" to save this setting
The following example uses the show module, show port index-allocation, and show module
recovery-steps commands to display a Generation 1 module that is powered down because of alignment,
even though contiguous indices 208 through 252 are available.
switch# show module
Mod Ports Module-Type Model Status
--- ----- -------------------------------- ------------------ ------------
1 48 1/2/4 Gbps FC Module DS-X9148 ok
2 48 1/2/4 Gbps FC Module DS-X9148 ok
4 48 1/2/4 Gbps FC Module DS-X9148 ok
5 0 Supervisor/Fabric-2 DS-X9530-SF2-K9 active *
6 0 Supervisor/Fabric-2 DS-X9530-SF2-K9 ha-standby
7 48 1/2/4 Gbps FC Module DS-X9148 ok
9 32 1/2 Gbps FC Module DS-X9032 powered-dn
Mod Power-Status Power Down Reason
--- ------------ ---------------------------
9 powered-dn Insufficient resources (dest Index)
switch# show port index-allocation
Module index distribution:
------------------------------------------------------+
Slot | Allowed | Alloted indices info |
| range | Total | Index values |
-----|---------|-------|------------------------------|
1 | 0-1023| 48 | 160-207 |
2 | 0-1023| 48 | 3-50 |

Cisco MDS 9000 Series Specifications

General

Category	Switch
Operating System	Cisco NX-OS
Ports	Varies by model
Protocols	Fibre Channel (FC), Fibre Channel over IP (FCIP), iSCSI
Redundancy	Redundant supervisors, power supplies, and fans
Management	Cisco Data Center Network Manager (DCNM), CLI, SNMP
Virtualization Support	VSANs (Virtual SANs)
Security Features	Fibre Channel Security Protocol (FC-SP)
Hot Swappable Components	power supplies, fans
Power Supply Options	AC and DC options available