EasyManuals Logo

Cisco MDS 9000 Series Command Reference

Cisco MDS 9000 Series
1464 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #1107 background imageLoading...
Page #1107 background image
Send documentation comments to mdsfeedback-doc@cisco.com
22-133
Cisco MDS 9000 Family Command Reference
OL-8413-07, Cisco MDS SAN-OS Release 3.x
Chapter 22 Show Commands
show interface
...
-------------------------------------------------------------------------------
Interface Input (rate is 5 min avg) Output (rate is 5 min avg)
----------------------------- -----------------------------
Rate Total Rate Total
MB/s Frames MB/s Frames
-------------------------------------------------------------------------------
iscsi4/1 0 0 0 0
iscsi4/2 0 0 0 0
iscsi4/3 0 0 0 0
iscsi4/4 0 0 0 0
...
vsan10 is up, line protocol is up
WWPN is 10:00:00:05:30:00:07:23, FCID is 0xee0001
Internet address is 10.1.1.5/24
MTU 1500 bytes, BW 1000000 Kbit
0 packets input, 0 bytes, 0 errors, 0 multicast
0 packets output, 0 bytes, 0 errors, 0 dropped
-------------------------------------------------------------------------------
Interface Input (rate is 5 min avg) Output (rate is 5 min avg)
----------------------------- -----------------------------
Rate Total Rate Total
MB/s Frames MB/s Frames
-------------------------------------------------------------------------------
port-channel 100 0 0 0 0
-------------------------------------------------------------------------------
Interface Input (rate is 5 min avg) Output (rate is 5 min avg)
----------------------------- -----------------------------
Rate Total Rate Total
Mbits/s Frames Mbits/s Frames
-------------------------------------------------------------------------------
fcip2 0 0 0 0
fcip3 9 0 9 0
fcip6 8 0 8 0
fcip7 8 0 8 0
The following example shows how to display information about a FCIP interface.
switch# show interface fcip 3
fcip3 is trunking
Hardware is GigabitEthernet
Port WWN is 20:ca:00:05:30:00:07:1e
Peer port WWN is 20:ca:00:00:53:00:18:1e
Admin port mode is auto, trunk mode is on
Port mode is TE
vsan is 1
Trunk vsans (allowed active) (1,10)
Trunk vsans (operational) (1)
Trunk vsans (up) (1)
Trunk vsans (isolated) (10)
Trunk vsans (initializing) ()
Using Profile id 3 (interface GigabitEthernet4/3)
Peer Information
Peer Internet address is 43.1.1.1 and port is 3225
Special Frame is disabled
Maximum number of TCP connections is 2
Time Stamp is disabled
B-port mode disabled
TCP Connection Information

Table of Contents

Other manuals for Cisco MDS 9000 Series

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco MDS 9000 Series and is the answer not in the manual?

Cisco MDS 9000 Series Specifications

General IconGeneral
CategorySwitch
Operating SystemCisco NX-OS
PortsVaries by model
ProtocolsFibre Channel (FC), Fibre Channel over IP (FCIP), iSCSI
RedundancyRedundant supervisors, power supplies, and fans
ManagementCisco Data Center Network Manager (DCNM), CLI, SNMP
Virtualization SupportVSANs (Virtual SANs)
Security FeaturesFibre Channel Security Protocol (FC-SP)
Hot Swappable Componentspower supplies, fans
Power Supply OptionsAC and DC options available

Related product manuals