Siemens SINAMICS G220 - Page 754

- 8060 -
1
Diagnostics Fault buffer
© Siemens AG
2 3 4 5 6 7 8
V6.02.00
<2>
RESET
r0949[63] [I32]
r2133[63] [Float]
r0945[0] r0947[0] r0945[1] r0947[1] r0945[7] r0947[7]
r0945[56] r0947[56] r0945[57] r0947[57] r0945[63] r0947[63]
r0945[8] r0947[8] r0945[9] r0947[9]
r0945[15] r0947[15]
r0949[0] [I32]
r2133[0] [Float]
r0949[1] [I32]
r2133[1] [Float]
r0949[7] [I32]
r2133[7] [Float]
r0949[56] [I32]
r2133[56] [Float]
r0949[57] [I32]
r2133[57] [Float]
r0949[8] [I32]
r2133[8] [Float]
r0949[9] [I32]
r2133[9] [Float]
r0949[15] [I32]
r2133[15] [Float]
r0948[0] [ms]
r2130[0] [d]
r0948[1] [ms]
r2130[1] [d]
r0948[7] [ms]
r2130[7] [d]
r0948[56] [ms]
r2130[56] [d]
r0948[57] [ms]
r2130[57] [d]
r0948[63] [ms]
r2130[63] [d]
r0948[8] [ms]
r2130[8] [d]
r0948[9] [ms]
r2130[9] [d]
r0948[15] [ms]
r2130[15] [d]
r2109[0] [ms]
r2136[0] [d]
r2109[1] [ms]
r2136[1] [d]
r2109[7] [ms]
r2136[7] [d]
r2109[56] [ms]
r2136[56] [d]
r2109[57] [ms]
r2136[57] [d]
r2109[63] [ms]
r2136[63] [d]
r2109[8] [ms]
r2136[8] [d]
r2109[9] [ms]
r2136[9] [d]
r2109[15] [ms]
r2136[15] [d]
<2>
r3120[63] r3120[57] r3120[56] r3120[15]
r3120[9] r3120[8] r3120[7] r3120[1] r3120[0]
r3122[63] r3122[57] r3122[56] r3122[15]
r3122[9] r3122[8] r3122[7] r3122[1] r3122[0]
Fault time received in milliseconds [ms]
r0948[0..63]
Fault time removed in milliseconds [ms]
r2109[0..63]
Fault time removed in days r2136[0..63]
Fault time received in days
r2130[0..63]
Fault code
r0945[0..63]
Fault number
r0947[0..63]
Fault value
r0949[0..63]
Fault value for float values
r2133[0..63]
c2103 [C]
(0)
1st acknowledge faults
c2104 [C]
(0)
2nd acknowledge faults
c2106 [C]
(1)
External fault 1
r0944
Counter for fault buffer changes
Fault cases counter
p0952 (0)
r2139 r2139.3
1 = Fault present
Component fault
r3120[0..63]
Diagnostic attribute fault
r3122[0..63].0..20
Fault
acknowl.
fault case
Acknowledge fault
1
Fault 2 Fault 8
<3>
Fault 1 Fault 2 Fault 8 Fault 1 Fault 2 Fault 8
1.
acknowl.
fault case
7.
(oldest)
Actual fault
case
Fault times
≥1
POWER ON
III
RESET
p0952 = 0: Fault buffer is deleted/cleared
Fault case appears Delete fault buffer
Fault appears
Fault disappears Fault case acknowl.
16 bit counter
16 bit counter free running
r0945 = 0, r0947 = 0 r0948 = 0, r0949 = 0 r2109 = 0, r2130 = 0 r2133 = 0, r2136 = 0 r3120 = 0, r3122 = 0
≥1
III
RESET
POWER ON
r2139 r2139.15
1 = Fault gone/can be acknowledged
<1>
The buffer parameters are cyclically updated in the background (refer to the status signal in r2139).
This fault is overwritten when "more recent" faults occur (with the exception of "safety faults").
Fault buffer change
,
Date
r8400[0..2]
Time
r8401[0..2]
[2548.2] [2548.2]
<3>
The fault code of the oldest active fault is displayed in r2131.
<1>
Figure15-8 8060 - Fault bu󹪜er
System messages
15.8Fault bu󹪜er
SINAMICS G220 converter
752 Operating Instructions, 04/2024, FW V6.2, A5E51781573B AB