Fujitsu PRIMERGY RX2540 M2 - Page 10

Upgrade and Maintenance Manual RX2540 M2
Contents
6.2.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 133
6.2.2 Removing the dummy cover . . . . . . . . . . . . . . . . . . 134
6.2.3 Installing a hot-plug PSU . . . . . . . . . . . . . . . . . . . . 134
6.2.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 135
6.3 Removing a hot-plug PSU . . . . . . . . . . . . . . . . . . 136
6.3.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 136
6.3.2 Note for servers using CMA (Cable Management Arm) . . . . 136
6.3.3 Removing a hot-plug PSU . . . . . . . . . . . . . . . . . . . 138
6.3.4 Installing a dummy cover . . . . . . . . . . . . . . . . . . . . 139
6.3.5 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 139
6.4 Replacing a hot-plug PSU . . . . . . . . . . . . . . . . . . . 140
6.4.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 140
6.4.2 Note for servers using CMA (Cable Management Arm) . . . . 140
6.4.3 Removing the defective hot-plug PSU . . . . . . . . . . . . . 141
6.4.4 Installing the new hot-plug PSU . . . . . . . . . . . . . . . . 141
6.4.5 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 141
7 Hard disk drives (HDD) and solid state drives (SSD) . . . . 143
7.1 Basic information . . . . . . . . . . . . . . . . . . . . . . . 144
7.2 3.5-inch cage configurations HDD/SSD . . . . . . . . . . . 144
7.2.1 Mounting order for 3.5-inch HDDs . . . . . . . . . . . . . . . 144
7.2.1.1 HDD mounting order for 4x 3.5-inch HDD configuration . . 145
7.2.1.2 HDD mounting order for 8x 3.5-inch HDD configurations . . 145
7.2.1.3 HDD mounting order for 12x 3.5-inch HDD configurations . 146
7.2.2 Installing 3.5-inch HDD modules . . . . . . . . . . . . . . . . 147
7.2.2.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . 147
7.2.2.2 Removing a 3.5-inch dummy module . . . . . . . . . . . . 148
7.2.2.3 Installing a 3.5-inch HDD module . . . . . . . . . . . . . . 149
7.2.2.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . 150
7.2.3 Removing 3.5-inch HDD modules . . . . . . . . . . . . . . . 150
7.2.3.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . 151
7.2.3.2 Removing a 3.5-inch HDD module . . . . . . . . . . . . . 152
7.2.3.3 Installing a 3.5-inch dummy module . . . . . . . . . . . . . 153
7.2.3.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . 153
7.2.4 Replacing a 3.5-inch HDD module . . . . . . . . . . . . . . . 154
7.2.4.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . 154
7.2.4.2 Removing a 3.5-inch HDD module . . . . . . . . . . . . . 154
7.2.4.3 Installing a 3.5-inch HDD module . . . . . . . . . . . . . . 155
7.2.4.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . 155