Fujitsu PRIMERGY RX2540 M2 - Page 16

Upgrade and Maintenance Manual RX2540 M2
Contents
8.6 GPGPU cards in riser modules (FL) . . . . . . . . . . . . . 283
8.6.1 Installing a GPGPU card in riser module 1 . . . . . . . . . . . 283
8.6.1.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . 283
8.6.1.2 Removing the slot cover from the riser card holder . . . . . 284
8.6.1.3 Installing a riser card with one PCIe slot Gen3 x16 . . . . . 285
8.6.1.4 Installing a GPGPU card in a riser module . . . . . . . . . 286
8.6.1.5 Replacing the heat sink (FL) . . . . . . . . . . . . . . . . 288
8.6.1.6 Removing the slot cover riser module 1 . . . . . . . . . . . 288
8.6.1.7 Removing the rear air grid riser module 1 . . . . . . . . . . 288
8.6.1.8 Installing the riser module 1 . . . . . . . . . . . . . . . . . 289
8.6.1.9 Installing the FBU on the riser card holder . . . . . . . . . 291
8.6.1.10 Installing the air duct riser module 1 . . . . . . . . . . . . 292
8.6.1.11 Concluding steps . . . . . . . . . . . . . . . . . . . . . . 295
8.6.2 Removing a GPGPU card from riser module 1 . . . . . . . . . 296
8.6.2.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . 296
8.6.2.2 Removing the FBU . . . . . . . . . . . . . . . . . . . . . 297
8.6.2.3 Removing the riser module 1 . . . . . . . . . . . . . . . . 297
8.6.2.4 Removing a GPGPU card (FL) . . . . . . . . . . . . . . . 298
8.6.2.5 Installing the slot cover riser module 1 . . . . . . . . . . . 298
8.6.2.6 Installing the air duct . . . . . . . . . . . . . . . . . . . . 298
8.6.2.7 Concluding steps . . . . . . . . . . . . . . . . . . . . . . 299
8.6.3 Installing a GPGPU card in riser module 2 . . . . . . . . . . . 299
8.6.3.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . 299
8.6.3.2 Removing the slot cover from the riser card holder . . . . . 299
8.6.3.3 Installing a riser card . . . . . . . . . . . . . . . . . . . . 299
8.6.3.4 Installing a GPGPU card in a riser module . . . . . . . . . 300
8.6.3.5 Installing the air grid extension to riser module 2 . . . . . . 300
8.6.3.6 Replacing the heat sink (FL) . . . . . . . . . . . . . . . . 300
8.6.3.7 Removing the rear air grid riser module 2 . . . . . . . . . . 300
8.6.3.8 Removing the slot cover riser module 2 . . . . . . . . . . . 301
8.6.3.9 Installing the riser module 2 (FL) . . . . . . . . . . . . . . 301
8.6.3.10 Installing the FBU riser module 2 . . . . . . . . . . . . . . 302
8.6.3.11 Installing the air duct riser module 2 . . . . . . . . . . . . 304
8.6.3.12 Concluding steps . . . . . . . . . . . . . . . . . . . . . . 306
8.6.4 Removing a GPGPU card in riser module 2 . . . . . . . . . . 307
8.6.4.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . 307
8.6.4.2 Removing the FBU . . . . . . . . . . . . . . . . . . . . . 307
8.6.4.3 Removing the riser module 2 . . . . . . . . . . . . . . . . 307
8.6.4.4 Removing the air grid extension from riser module 2 (FL) . 308
8.6.4.5 Removing a GPGPU card . . . . . . . . . . . . . . . . . . 308
8.6.4.6 Installing the slot cover riser module 2 . . . . . . . . . . . 308
8.6.4.7 Installing the rear air grid riser module 2 . . . . . . . . . . 308