Mitsubishi FR-A800

(A) Application parameters
PARAMETERS
463
5
GROUP
A
5.14 (A) Application parameters
Purpose Parameter to set
Refer
to
page
To operate by switching between
the inverter and the commercial
power supply operation
Electronic bypass function P.A000 to P.A005
Pr.135 to Pr.139,
Pr.159
464
To reduce the standby power Self power management
P.A002, P.A006,
P.A007, P.E300
Pr.30, Pr.137,
Pr.248, Pr.254
470
To stop the motor with a
mechanical brake (operation
timing of mechanical brake)
Brake sequence function
P. A 1 0 0 t o P. A 1 0 6 ,
P.F500, P.A108,
P.A109,
P. A 1 2 0 t o P. A 1 3 0
Pr.278 to Pr.285,
Pr.292,
Pr.639 to Pr.651
473
To stop the motor with a
mechanical brake
(vibration control at stop-on-
contact)
Stop-on-contact control
P.A200, P.A205,
P. A 20 6
Pr.270, Pr.275,
Pr.276
478
To increase the speed at light
load
Load torque high-speed
frequency control
P.D301, P.D302
P. A 2 0 0 t o P. A 2 0 4
Pr.4, Pr.5,
Pr.270 to Pr.274
481
To strengthen or weaken the
frequency at a constant cycle
Traverse operation P.A300 to P.A305 Pr.592 to Pr.597 484
To suppress the swinging of an
object moved by a crane by
crane control
Swinging suppression
control
P.A310 to P.A317 Pr.1072 to Pr.1079 486
To adjust the stop position
(orientation control) of the
rotating shaft
Orientation control
P. A 5 1 0 t o P. A 5 1 2 ,
P.A520, P.A524,
P.A525,
P. A 5 2 6 t o P. A 5 3 3 ,
P. A 5 4 2 t o P. A 5 4 5 ,
P.C140, P.C141
Pr.350 to Pr.366,
Pr.369, Pr.393,
Pr.396 to Pr.399
488
To perform process control,
such as for the pump flow
volume and air volume
PID control
P. A 6 0 0 t o P. A 6 0 7 ,
P. A 6 1 0 t o P. A 6 1 5 ,
P. A 6 2 1 t o P. A 6 2 5 ,
P. A 6 4 0 t o P. A 6 4 4 ,
P. A 6 5 0 t o P. A 6 5 5 ,
P. A 6 6 1 t o P. A 6 6 5
Pr.127 to Pr.134,
Pr.553, Pr.554,
Pr.575 to Pr.577,
Pr.609, Pr.610,
Pr.753 to Pr.758,
Pr.1015, Pr.1134,
Pr.1135, Pr.1140,
Pr.1141,
Pr.1143 to Pr.1149
501
PID pre-charge function
P. A 6 1 6 t o P. A 6 2 0 ,
P. A 6 5 6 t o P. A 6 6 0
Pr.760 to Pr.769 517
PID display adjustment
P. A 6 3 0 t o P. A 6 3 3 ,
P. A 6 7 0 t o P. A 6 7 3
C42 to C45
(Pr.934, Pr.935),
Pr.1136 to Pr.1139
514
To control the dance roll for
winding/unwinding
Dancer control
P.A601, P.A602,
P.A605, P.A606,
P.A610, P.A611,
P.A613, P.A615,
P
.A624, P.A625,
P.F020, P.F021
Pr.44, Pr.45,
Pr.128, Pr.134,
Pr.609, Pr.610,
Pr.1134, Pr.1135
521
To continue operating at analog
current input loss
4 mA input check P.A680 to P.A682
Pr.573, Pr.777,
Pr.778
426
To restart without stopping the
motor at instantaneous power
failure
Automatic restart after
instantaneous power failure
/ flying start function for
induction motors
P. A 7 0 0 t o P. A 7 0 5 ,
P.A710, P.F003
Pr.57, Pr.58,
Pr.162 to Pr.165,
Pr.299, Pr.611
528
Frequency search accuracy
improvement (V/F control,
offline auto tuning)
P.A700, P.A711,
P.A712, P.C110,
P. C 21 0
Pr.96, Pr.162,
Pr.298, Pr.463,
Pr.560
536
Automatic restart after
instantaneous power failure
/ flying start function for
IPM motors
P.A700, P.A702,
P.F003, P.F004
Pr.57, Pr.162,
Pr.611
534