Mitsubishi FR-A800

Parameter List
Parameter list (by function group)
150
PARAMETERS
 D: Operation command and frequency
command
Parameters that specify the inverter's command source, and
parameters that set the motor driving frequency and torque.
 H: Protective function parameter
Parameters to protect the motor and the inverter.
Pr.
group
Pr. Name
Refer
to page
D000 79
Operation mode selection
306,
315
D001 340
Communication startup mode selection
315
D010 338
Communication operation command
source
316
D011 339
Communication speed command
source
316
D012 550
NET mode operation command source
selection
316
D013 551
PU mode operation command source
selection
316
D020 78
Reverse rotation prevention selection
323
D030 811
Set resolution switchover
185,
357
D100 291
Pulse train I/O selection
324,
369
D101 384
Input pulse division scaling factor
324
D110 385
Frequency for zero input pulse
324
D111 386
Frequency for maximum input pulse
324
D200 15
Jog frequency
327
D300 28
Multi-speed input compensation
selection
328
D301 4
Multi-speed setting (high speed)
328
D302 5
Multi-speed setting (middle speed)
328
D303 6
Multi-speed setting (low speed)
328
D304
to
D307
24 to
27
Multi-speed setting (4 speed to 7 speed)
328
D308
to
D315
232 to
239
Multi-speed setting (8 speed to 15
speed)
328
D400 804
Torque command source selection
216
D401 805
Torque command value (RAM)
216
D402 806
Torque command value (RAM,EEPROM)
216
D403 1114
Torque command reverse selection
216
Pr.
group
Pr. Name
Refer
to page
H000 9
Electronic thermal O/L relay
331,
442,
452
H001 600
First free thermal reduction frequency 1
331
H002 601
First free thermal reduction ratio 1
331
H003 602
First free thermal reduction frequency 2
331
H004 603
First free thermal reduction ratio 2
331
H005 604
First free thermal reduction frequency 3
331
H006 607
Motor permissible load level
331
H010 51
Second electronic thermal O/L relay
331,
442,
452
H011 692
Second free thermal reduction
frequency 1
331
H012 693
Second free thermal reduction ratio 1
331
H013 694
Second free thermal reduction
frequency 2
331
H014 695
Second free thermal reduction ratio 2
331
Simple
Simple
Simple
Simple
Simple
Simple
Simple
Simple
Simple
Simple
Simple
Simple
Simple
Simple
Simple
H015 696
Second free thermal reduction
frequency 3
331
H016 608
Second motor permissible load level
331
H020 561
PTC thermistor protection level
331
H021 1016
PTC thermistor protection detection
time
331
H030 875
Fault definition
339
H100 244
Cooling fan operation selection
340
H101 249
Earth (ground) fault detection at start
613
H102 598 
Undervoltage level
341
H103 997
Fault initiation
342
H200 251
Output phase loss protection selection
342
H201 872 
Input phase loss protection selection
342
H300 65
Retry selection
343
H301 67
Number of retries at fault occurrence
343
H302 68
Retry waiting time
343
H303 69
Retry count display erase
343
H400 1
Maximum frequency
345
H401 2
Minimum frequency
345
H402 18
High speed maximum frequency
345
H410 807
Speed limit selection
219
H411 808
Forward rotation speed limit/speed limit
219
H412 809
Reverse rotation speed limit/reverse-
side speed limit
219
H414 1113
Speed limit method selection
219
H415 873 
Speed limit
206
H416 285
Speed deviation excess detection
frequency
206,
473,
626
H417 853 
Speed deviation time
206
H420 31
Frequency jump 1A
346
H421 32
Frequency jump 1B
346
H422 33
Frequency jump 2A
346
H423 34
Frequency jump 2B
346
H424 35
Frequency jump 3A
346
H425 36
Frequency jump 3B
346
H429 552
Frequency jump range
346
H500 22
Stall prevention operation level (Torque
limit level)
185,
348
H501 156
Stall prevention operation selection
348
H600 48
Second stall prevention operation level
348
H601 49
Second stall prevention operation
frequency
348
H602 114
Third stall prevention operation level
348
H603 115
Third stall prevention operation
frequency
348
H610 23
Stall prevention operation level
compensation factor at double speed
348
H611 66
Stall prevention operation reduction
starting frequency
348
H620 148
Stall prevention level at 0 V input
348
H621 149
Stall prevention level at 10 V input
348
H631 154
Voltage reduction selection during stall
prevention operation
348
H700 810
Torque limit input method selection
185
H701 812
Torque limit level (regeneration)
185
H702 813
Torque limit level (3rd quadrant)
185
H703 814
Torque limit level (4th quadrant)
185
H710 815
Torque limit level 2
185
H720 816
Torque limit level during acceleration
185
H721 817
Torque limit level during deceleration
185
H730 874
OLT level setting
185
H800 374
Overspeed detection level
355
H881 690
Deceleration check time
207
Pr.
group
Pr. Name
Refer
to page
Simple
Simple
Simple
Simple
Simple
Simple