Mitsubishi FR-A800 - Page 714

APPENDIX
713
93 Motor constant (L2)/q-axis inductance (Lq) 5D DD 0            
94 Motor constant (X) 5E DE 0      
95 Online auto tuning selection 5F DF 0            
96 Auto tuning setting/status 60 E0 0    
100 V/F1 (first frequency) 00 80 1            
101 V/F1 (first frequency voltage) 01 81 1  
102 V/F2 (second frequency) 02 82 1            
103 V/F2 (second frequency voltage) 03 83 1  
104 V/F3 (third frequency) 04 84 1            
105 V/F3 (third frequency voltage) 05 85 1  
106 V/F4 (fourth frequency) 06 86 1            
107 V/F4 (fourth frequency voltage) 07 87 1  
108 V/F5 (fifth frequency) 08 88 1            
109 V/F5 (fifth frequency voltage) 09 89 1  
110 Third acceleration/deceleration time 0A 8A 1    

  

  
111 Third deceleration time 0B 8B 1 




112 Third torque boost 0C 8C 1            
113 Third V/F (base frequency) 0D 8D 1  
114 Third stall prevention operation level 0E 8E 1            
115 Third stall prevention operation frequency 0F 8F 1  
116 Third output frequency detection 10 90 1            
117 PU communication station number 11 91 1  

 
118 PU communication speed 12 92 1          
 
119
PU communication stop bit length / data
length
13 93 1  

 
120 PU communication parity check 14 94 1          
 
121 Number of PU communication retries 15 95 1  

 
122 PU communication check time interval 16 96 1          
 
123 PU communication waiting time setting 17 97 1  

 
124 PU communication CR/LF selection 18 98 1          
 
125 Terminal 2 frequency setting gain frequency 19 99 1      
126 Terminal 4 frequency setting gain frequency 1A 9A 1            
127 PID control automatic switchover frequency 1B 9B 1 




128 PID action selection 1C 9C 1            
129 PID proportional band 1D 9D 1     
130 PID integral time 1E 9E 1            
131 PID upper limit 1F 9F 1     
132 PID lower limit 20 A0 1            
133 PID action set point 21 A1 1     
134 PID differential time 22 A2 1            
135 Electronic bypass sequence selection 23 A3 1  
136 MC switchover interlock time 24 A4 1            
137 Start waiting time 25 A5 1  
138 Bypass selection at a fault 26 A6 1            
139
Automatic switchover frequency from
inverter to bypass operation
27 A7 1  
140 Backlash acceleration stopping frequency 28 A8 1            
141 Backlash acceleration stopping time 29 A9 1    
142 Backlash deceleration stopping frequency 2A AA 1            
143 Backlash deceleration stopping time 2B AB 1    
144 Speed setting switchover 2C AC 1            
145 PU display language selection 2D AD 1  

147
Acceleration/deceleration time switching
frequency
2F AF 1    

  

  
148 Stall prevention level at 0 V input 30 B0 1  
149 Stall prevention level at 10 V input 31 B1 1            
150 Output current detection level 32 B2 1  
151 Output current detection signal delay time 33 B3 1            
Pr. Name
Instruction
code

Control method Parameter
Read
Write
Extended
Copy Clear
All clear
Speed
control
Torque
control
Position
control
Speed
control
Torque
control
Speed
control
Position
control
V/FV/FV/F
Magnetic fluxMagnetic fluxMagnetic flux
VectorVectorVector
SensorlessSensorlessSensorless
PMPMPM