Mitsubishi FR-A800

Parameter List
Parameter list (by function group)
154
PARAMETERS
A312 1074
Swinging suppression frequency
486
A313 1075
Swinging suppression depth
486
A314 1076
Swinging suppression width
486
A315 1077
Rope length
486
A316 1078
Trolley weight
486
A317 1079
Load weight
486
A510 350 
Stop position command selection
488
A511 360 
16-bit data selection
488
A512 361 
Position shift
488
A520 362 
Orientation position loop gain
488
A521 363 
Completion signal output delay time
488
A522 364 
Encoder stop check time
488
A523 365 
Orientation limit
488
A524 366 
Recheck time
488
A525 393 
Orientation selection
488
A526 351 
Orientation speed
488
A527 352 
Creep speed
488
A528 353 
Creep switchover position
488
A529 354 
Position loop switchover position
488
A530 355 
DC injection brake start position
488
A531 356 
Internal stop position command
488
A532 357 
Orientation in-position zone
488
A533 358 
Servo torque selection
488
A542 396 
Orientation speed gain (P term)
488
A543 397 
Orientation speed integral time
488
A544 398 
Orientation speed gain (D term)
488
A545 399 
Orientation deceleration ratio
488
A600 759
PID unit selection
514
A601 131
PID upper limit
501,
521
A602 132
PID lower limit
501,
521
A603 553
PID deviation limit
501
A604 554
PID signal operation selection
501
A605 1134
PID upper limit manipulated value
521
A606 1135
PID lower limit manipulated value
521
A607 1015
Integral stop selection at limited
frequency
501
A610 128
PID action selection
501,
521
A611 133
PID action set point
501,
521
A612 127
PID control automatic switchover
frequency
501
A613 129
PID proportional band
501,
521
A614 130
PID integral time
501,
521
A615 134
PID differential time
501,
521
A616 760
Pre-charge fault selection
517
A617 761
Pre-charge ending level
517
A618 762
Pre-charge ending time
517
A619 763
Pre-charge upper detection level
517
A620 764
Pre-charge time limit
517
A621 575
Output interruption detection time
501
A622 576
Output interruption detection level
501
A623 577
Output interruption cancel level
501
A624 609
PID set point/deviation input selection
501,
521
A625 610
PID measured value input selection
501,
521
Pr.
group
Pr. Name
Refer
to page
A630
C42
(934)

PID display bias coefficient
514
A631
C43
(934)

PID display bias analog value
514
A632
C44
(935)

PID display gain coefficient
514
A633
C45
(935)

PID display gain analog value
514
A640 1142
Second PID unit selection
501
A641 1143
Second PID upper limit
501
A642 1144
Second PID lower limit
501
A643 1145
Second PID deviation limit
501
A644 1146
Second PID signal operation selection
501
A650 753
Second PID action selection
501
A651 755
Second PID action set point
501
A652 754
Second PID control automatic
switchover frequency
501
A653 756
Second PID proportional band
501
A654 757
Second PID integral time
501
A655 758
Second PID differential time
501
A656 765
Second pre-charge fault selection
517
A657 766
Second pre-charge ending level
517
A658 767
Second pre-charge ending time
517
A659 768
Second pre-charge upper detection
level
517
A660 769
Second pre-charge time limit
517
A661 1147
Second output interruption detection
time
501
A662 1148
Second output interruption detection
level
501
A663 1149
Second output interruption cancel level
501
A664 1140
Second PID set point/deviation input
selection
501
A665 1141
Second PID measured value input
selection
501
A670 1136
Second PID display bias coefficient
514
A671 1137
Second PID display bias analog value
514
A672 1138
Second PID display gain coefficient
514
A673 1139
Second PID display gain analog value
514
A680 573
4 mA input check selection
426
A681 777
4 mA input fault operation frequency
426
A682 778
4 mA input check filter
426
A700 162
Automatic restart after instantaneous
power failure selection
528,
534,
536
A701 299
Rotation direction detection selection at
restarting
528
A702 57
Restart coasting time
528,
534
A703 58
Restart cushion time
528
A704 163
First cushion time for restart
528
A705 164
First cushion voltage for restart
528
A710 165
Stall prevention operation level for
restart
528
A711 298
Frequency search gain
536
A712 560
Second frequency search gain
536
A730 261
Power failure stop selection
540
A731 262
Subtracted frequency at deceleration
start
540
A732 263
Subtraction starting frequency
540
Pr.
group
Pr. Name
Refer
to page