IMC CANSAS - Page 8

© 2014 imc Meßsysteme GmbH imc CANSAS Users Manual - Doc. Version 1.9 - 05.12.2014
8 Table Of Contents
............................................................................................................................................. 285
6.6 DAC8 analog outputs
.................................................................................................................................. 2856.6.1 General notes DAC8
.................................................................................................................................. 2856.6.2 Analog portion
.................................................................................................................................. 2866.6.3 Linking the output signal to a CAN-message
.................................................................................................................................. 2876.6.4 Message Mapping
.................................................................................................................................. 2886.6.5 Calculating the output signal
.................................................................................................................................. 2896.6.6 Configuring the outputs
.................................................................................................................................. 2896.6.7 CANSAS-DAC8 block diagram
.................................................................................................................................. 2906.6.8 Taking measurements with the analog output modules
.................................................................................................................................. 2916.6.9 Connector plugs DAC8
............................................................................................................................................. 292
6.7 DCB8: bridge, strain gauges
.................................................................................................................................. 2936.7.1 Bridge measurement
...................................................................................................................... 2946.7.1.1 Full bridge
...................................................................................................................... 2946.7.1.2 Half bridge
...................................................................................................................... 2956.7.1.3 Quarter bridge
...................................................................................................................... 2966.7.1.4 Sense and initial unbalance
...................................................................................................................... 2976.7.1.5 Balancing and shunt calibration
.................................................................................................................................. 2986.7.2 Voltage measurement
...................................................................................................................... 2986.7.2.1 Voltage source with ground reference
...................................................................................................................... 2986.7.2.2 Voltage source without ground reference
...................................................................................................................... 2996.7.2.3 Voltage source at a different fixed potential
...................................................................................................................... 2996.7.2.4 Voltage measurement: With zero-adjusting (tare)
.................................................................................................................................. 3006.7.3 Sensor supply
.................................................................................................................................. 3006.7.4 Bandwidth
.................................................................................................................................. 3006.7.5 Connection
............................................................................................................................................. 301
6.8 DI16 digital inputs
.................................................................................................................................. 3016.8.1 Overview
.................................................................................................................................. 3016.8.2 Settings
.................................................................................................................................. 3026.8.3 Block diagram
.................................................................................................................................. 3026.8.4 Sampling Interval
.................................................................................................................................. 3036.8.5 CAN-bus message dialog
.................................................................................................................................. 3036.8.6 Connector plugs DI16
............................................................................................................................................. 304
6.9 DO16 digital outputs
.................................................................................................................................. 3046.9.1 Configuring the outputs
.................................................................................................................................. 3046.9.2 Starting up the DO16 module
.................................................................................................................................. 3046.9.3 CANSAS-DO16 block diagram
...................................................................................................................... 3046.9.3.1 Open Drain Mode
...................................................................................................................... 3056.9.3.2 Totem-Pole Mode
.................................................................................................................................. 3066.9.4 Invert Output
.................................................................................................................................. 3076.9.5 Connector plugs DO16
............................................................................................................................................. 308
6.10 DO8R, -DO16R relay outputs
.................................................................................................................................. 3086.10.1 block diagram DO8R, DO16R
.................................................................................................................................. 3096.10.2 Starting the DO8R, DO16R module
.................................................................................................................................. 3096.10.3 Connector plugs DO8R, DO16R
............................................................................................................................................. 310
6.11 IGN ignition angle measurement module
.................................................................................................................................. 3146.11.1 Interference suppression
.................................................................................................................................. 3156.11.2 Housing
...................................................................................................................... 3156.11.2.1 Grounding bolt
...................................................................................................................... 3156.11.2.2 LEDs
...................................................................................................................... 3156.11.2.3 Display
.................................................................................................................................. 3166.11.3 Operation modes
...................................................................................................................... 3166.11.3.1 Default operation type
...................................................................................................................... 3176.11.3.2 Snapshot operation mode
.................................................................................................................................. 3206.11.4 Parameterization
...................................................................................................................... 3276.11.4.1 The channel's parameters
...................................................................................................................... 3296.11.4.2 Offset adjustment
.................................................................................................................................. 3306.11.5 Tips