Index I-5
7510
ADF feeder roll 7-48
ADF left cover components 7-44
ADF media guide 7-46
ADF motor unit 7-50
miscellaneous 7-92
Pound button 2-3
preventive maintenance 6-1
printer overview 1-3
basic model 1-3
configured model 1-4
printer technology 1-1
printer theory 1-5
control 1-26
ADF document size detection 1-52
document scanning steps 1-54
document size detection at scanner unit assembly
1-50
fuser control 1-27
media size control 1-26
printhead control 1-26
document scanning 1-34
document scanning at ADF 1-35
document scanning at platen 1-34
drive 1-20
CMY developer drive motor assembly 1-22
CMY toner add motor assembly 1-22
CMYK PC cartridge drive motor assembly 1-21
K developer clutch 1-22
K developer/transport drive motor assembly 1-20
MPF/transport drive motor 1-20
waste toner agitator motor assembly 1-23
drive torque transfer scheme 1-42
ADF feed motor assembly 1-42
ADF registration motor 1-42
electrical components and controller 1-23
exit 1-19, 1-20
functions of main components 1-7
bottom plate 1-8
end guide 1-8
media tray assembly 1-7
rear media guide 1-8
image data flow 1-41
media size 1-10
media transport 1-5
media transport path 1-5
MFP sensors 1-7
media tray assembly 1-8
detection of media size 1-8
media feed unit assembly 1-8
media feed/lift motor 1-9
sensor (feed-out) 1-9
sensor (media level) 1-9
sensor (media out) 1-9
switch (media size) 1-9, 1-61
multi-purpose feeder (MPF) 1-9
MPF feed roll 1-10
MPF pick solenoid 1-10
sensor (MPF media out) 1-10
sensor (MPF media width) 1-10
names and functions of components 1-45
ADF 1-46
scanner unit assembly 1-45
printhead assembly 1-14
front thermistor 1-19
fuser exit sensor 1-19
heat roll 1-18
heater lamp 1-19
pressure belt 1-19
printhead shutter 1-17
rear thermistor 1-19
thermostat 1-19
registration 1-11
media transport roll assembly 1-11
registration clutch 1-11
registration roll assembly 1-11
sensor (registration) 1-11
sensor (transparency detect) 1-11
standard media exit roll assembly 1-20
duplex diverter gate 1-20
sensor (standard bin full) 1-20
standard media exit shift motor 1-20
transfer 1-12
2nd transfer roll assembly 1-13
2nd transfer roll retract motor 1-13
sensor (2nd transfer roll HP) 1-14
transfer belt cleaning assembly 1-12
transfer belt drive motor assembly 1-12
transfer belt steering motor 1-13
transfer belt unit assembly 1-13
xerographic process during a print cycle 1-28
processor 1-1
R
radio button
selected
2-10
unselected 2-10
removals
duplex media inverter assembly
4-9
duplex unit assembly 4-10
feed roll 4-115
front left cover 4-9
MPF feed unit assembly 4-8
pick roll 4-116
printer front door assembly 4-3
printer left lower door assembly 4-8
rear cover assembly 4-5
rear left middle cover 4-6
rear left upper cover 4-7
right cover assembly 4-4
sensor (media level) 4-34
sensor (media out) 4-32
sensor (RFID PC cartridge) and sensor (RFID toner
cartridge)
4-117
separation roll 4-117
switch (media size) 4-121, 4-189
top cover assembly 4-4
removals—2000-sheet dual input (TTM)
2TM/TTM controller card assembly
4-212, 4-238,
4-259
To Next Page
Loading...
Need help?
General
