Lexmark X945e MFP 7510 series User Manual

Index I-3
7510
Go Back
Previous
Next
842.01 scanner communication failure 2-111
842.02 scanner communication failure 2-112
842.03 scanner communication failure 2-112
842.04 scanner communication failure 2-113
842.10 scanner unit assembly - ADF communication
failure
2-113
842.11 scanner communication failure (by scanner)
2-114
842.12 scanner unit assembly communication failure
2-114
843.00 sensor (scanner HP) failure 2-115
843.01 scanner carriage over run failure 2-116
843.10 ADF RAM test failure 2-117
843.11 ADF EEPROM failure 2-117
843.12 ADF pick roll position lift up failure 2-117
843.20 scanner unit assembly connection failure 2-119
843.21 scanner unit assembly EEPROM failure 2-119
843.22 scanner unit assembly EEPROM sub system
failure
2-119
843.23 scanner cooling fan failure 2-120
843.24 image processing failure 2-121
843.25 scanner controller card assembly failure 2-121
843.26 scanner controller card assembly failure 2-122
844.00 exposure lamp error 2-122
844.01 white reference/exposure lamp illumination error
2-123
845.00 CCD error 2-124
845.01 CCD initialization (lamp on) error 2-125
845.02 CCD initialization (lamp off) error 2-126
846.00 scanner communication error 2-126
846.01 scanner communication error 2-127
846.10 sensor (ADF width APS X) error 2-127
846.12 scanner unit assembly software logic error
2-129
846.13 switch (platen interlock) open 2-129
847.00 modem error 2-130
847.01 fax storage error 2-130
848.00 Fax/modem configuration ID mismatch 2-131
849.00 hard drive/configuration ID mismatch 2-131
901.XX RIP card assembly software error 2-134,
2-135, 2-136, 2-137, 2-138, 2-139, 2-140, 2-141
903.00 K developer/transport drive assembly motor
error
2-142
903.01 K PC drive motor error 2-143
903.02 CMY PC drive motor error 2-144
903.03 developer drive motor error 2-145
904.00 NVM data failure 2-151
904.00 Sensor (transfer belt HP) late error 2-146
904.01 transfer belt position failure 2-151
904.02 Sensor (transfer belt edge) failure 2-156
904.03 sensor (2nd transfer roll retract HP) late error
2-159
904.04 sensor (2nd transfer roll retract HP) lag error
2-160
904.05 sensor (CMY transfer roll retract HP) late error
2-162
904.06 sensor (CMY transfer roll retract HP) lag error
2-164
904.07 CMY transfer roll retract motor time out 2-166
905.00 NVM read/write cannot be executed failure
2-167
905.01 marking device video error 2-167
905.02 marking device Xerographics error 2-168
905.03 marking device other1 error 2-168
905.04 marking device paper handling error 2-168
905.05 marking device other2 error 2-168
907.00 printhead polygon mirror motor error 2-168
907.01 SOS internal error 2-169
907.02 SOS internal error 2-169
907.03 SOS internal error 2-170
907.04 SOS internal error 2-170
907.05 printhead control error 2-171
908.00 waste toner full error 2-171
911.00 24V LVPS cooling fan error 2-172
911.01 transfer belt drive motor cooling fan error 2-172
911.02 fuser cooling fan lock error 2-173
918.00 standard media exit shift error 2-173
920.00 fuser main lamp overheat error 2-174
920.01 front thermistor disconnection error 2-174
920.01 magenta toner RFID communication error
2-179, 2-184
920.02 fuser sub lamp overhead error 2-175
920.03 rear thermistor disconnection error 2-175
920.04 main lamp warm up error 2-176
920.05 main lamp on-time error 2-177
920.06 sub lamp warm-up failure 2-177
920.07 sub lamp on-time error 2-178
924.00 yellow toner RFID communication error 2-178,
2-183
924.02 cyan toner RFID communication error 2-180,
2-184
924.03 black toner RFID communication error 2-180,
2-184
925.00 fsensor (C ATC) error 2-182
925.00 sensor (K ATC) error 2-183
925.00 sensor (M ATC) error 2-181
925.00 sensor (Y ATC) error 2-181
940.00 MPF tray 5 size sensing error 2-185
941.00 switch (media size) size sensing error (tray 1)
2-185
941.01 sensor (media level) late error (tray 1) 2-186
942.00 switch (media size) size sensing error (tray 2)
2-187
942.01 sensor (media level) late error (tray 2) 2-188
943.00 switch (media size) size sensing error (tray 3)
2-189
943.01 sensor (media level) late error (tray 3) 2-190
944.00 switch (media size) size sensing error (tray 4)
2-191
944.01 sensor (media level) late error (tray 4) 2-192
950.00 through 950.29 EPROM mismatch failure 2-193
950.30 through 950.60 EPROM mismatch failure 2-193
951.XX RIP card assembly NVRAM failure 2-194
952.XX Interconnect card NVRAM CRC failure 2-194
953.XX operator panel assembly NVRAM failure 2-195
954.XX interconnect card assembly NVRAM failure
2-195
955.XX RIP card assembly NAND CRC failure 2-196

Lexmark X945e MFP 7510 series Specifications

General

Brand	Lexmark
Model	X945e MFP 7510 series
Category	Printer
Language	English