Schweitzer Engineering Laboratories SEL-751 - Page 10

viii
SEL-751 Relay Instruction Manual Date Code 20170927
List of Tables
Table 7.9 ANALOG Command ........................................................................................................... 7.23
Table 7.10 COM Command ................................................................................................................... 7.28
Table 7.11 CONTROL Command ......................................................................................................... 7.28
Table 7.12 Three Remote Bit States....................................................................................................... 7.29
Table 7.13 COPY Command.................................................................................................................. 7.29
Table 7.14 COUNTER Command ......................................................................................................... 7.29
Table 7.15 Date Command..................................................................................................................... 7.29
Table 7.16 EVENT Command (Event Reports)..................................................................................... 7.32
Table 7.17 FILE Command.................................................................................................................... 7.32
Table 7.18 GOOSE Command Variants.................................................................................................7.33
Table 7.19 GROUP Command............................................................................................................... 7.36
Table 7.20 HELP Command .................................................................................................................. 7.36
Table 7.21 HISTORY Command ........................................................................................................... 7.37
Table 7.22 HIS HIF Command .............................................................................................................. 7.37
Table 7.23 HSG Command .................................................................................................................... 7.38
Table 7.24 IDENTIFICATION Command............................................................................................. 7.39
Table 7.25 INI HIF Command ............................................................................................................... 7.39
Table 7.26 IRI Command....................................................................................................................... 7.39
Table 7.27 LDP Commands................................................................................................................... 7.40
Table 7.28 L_D Command (Load Firmware) ........................................................................................ 7.40
Table 7.29 LOG HIF Command............................................................................................................. 7.41
Table 7.30 LOO Command.................................................................................................................... 7.41
Table 7.31 Meter Command................................................................................................................... 7.42
Table 7.32 Meter Class........................................................................................................................... 7.43
Table 7.33 PASSWORD Command.......................................................................................................7.44
Table 7.34 Factory-Default Passwords for Access Levels 1, 2, and C................................................... 7.44
Table 7.35 Valid Password Characters................................................................................................... 7.44
Table 7.36 PUL OUTnnn Command ..................................................................................................... 7.46
Table 7.37 QUIT Command................................................................................................................... 7.46
Table 7.38 R_S Command (Restore Factory-Defaults) ......................................................................... 7.46
Table 7.39 SER Command (Sequential Events Recorder Report)......................................................... 7.47
Table 7.40 SER D Command................................................................................................................. 7.47
Table 7.41 SET Command (Change Settings) ....................................................................................... 7.48
Table 7.42 SET Command Editing Keystrokes...................................................................................... 7.48
Table 7.43 SHOW Command (Show/View Settings)............................................................................. 7.49
Table 7.44 STATUS Command (Relay Self-Test Status)....................................................................... 7.51
Table 7.45 STATUS Command Report and Definitions ........................................................................ 7.51
Table 7.46 SUMMARY Command........................................................................................................7.53
Table 7.47 SUM HIF Command............................................................................................................ 7.53
Table 7.48 TARGET Command (Display Relay Word Bit Status)........................................................ 7.53
Table 7.49 Front-Panel LEDs and the TAR 0 Command....................................................................... 7.54
Table 7.50 TEST DB Commands........................................................................................................... 7.54
Table 7.51 THE Command (Preload or Reset Thermal Capacity)......................................................... 7.56
Table 7.52 TIME Command (View/Change Time)................................................................................ 7.56
Table 7.53 TRIGGER Command (Trigger Event Report) ..................................................................... 7.57
Table 7.54 TRIGGER HIF Command ................................................................................................... 7.57
Table 7.55 VEC Command .................................................................................................................... 7.57
Table 7.56 FTP and MMS Virtual File Structure................................................................................... 7.58
Table 7.57 Settings Directory Files........................................................................................................ 7.60
Table 7.58 Reports Directory Files ........................................................................................................ 7.60
Table 7.59 Event Directory Files ........................................................................................................... 7.61
Table 7.60 Files Available for Ymodem Protocol.................................................................................. 7.62
Table 7.61 FTP and MMS Wildcard Usage Examples .......................................................................... 7.63
Table 7.62 Ymodem Wildcard Usage Examples ................................................................................... 7.63
Table 8.1 Front-Panel Automatic Messages (FP_AUTO := OVERRIDE) ............................................ 8.3
Table 8.2 Front-Panel Pushbutton Functions ......................................................................................... 8.5
Table 8.3 Possible Warning Conditions (Flashing TRIP LED) ........................................................... 8.14
Table 8.4 SEL-751 Front-Panel Operator Control Functions .............................................................. 8.16