Schweitzer Engineering Laboratories SEL-751 - Page 916

IN.4 Index
P–S
SEL-751 Relay Instruction Manual Date Code 20170927
Overvoltage Elements
logic diagram
, 4.100
P
Password
access level
, 7.20–7.21
change
, 7.45
factory default
, 7.44
front panel, 8.3
jumper
, 2.18
Phase Overcurrent Elements
See Overcurrent Elements
Phase Rotation
, 4.169
phasor diagram
, 4.169
setting, PHROT, 4.169
Port Settings (SET P Command)
, 4.188
Power
functional test
, 11.8
meter
, 5.3
power measurement convention
, 5.2
Power Factor
elements
, 4.117
logic diagram
, 4.118
functional test
, 11.8
measurement convention, 5.2
meter
, 5.3
Power Supply
fuse ratings
, 2.50
Protocols
C37.118 (Synchrophasors)
, I.1–I.18
Pushbuttons
, 8.2–8.4, 8.14
navigation
, 8.5
target reset
, 8.14–8.15
R
Rack Mounting Accessory, 1.7
Reactive
power measurement convention
, 5.2
Reactive Power
, 5.2
meter
, 5.3
Real Power
, 5.2
See also Meter
meter
, 5.3
Rear Panel
, 2.19
Reclose Logic
, 4.137–4.153
Reclose Supervision Logic
, 4.131
Relay Word Bits
, K.1
row list
, K.6
Remote Analogs
, C.11
integer, float, or long data types
, C.13
metering
, 5.12
populating DNP analog output map
with
, D.28
Remote Trip
, 4.128
control input
, 4.130
Replacement Rear Connector Kit, 1.7
Report Settings
, 4.205
Event report
, 4.207
SER trigger, 4.206
Reset
targets
, 8.14
Resistance Temperature Detector
See also Meter
alarm temperatures, 4.90
failure messages, 5.6
location settings
, 4.89
status messages
, 5.6
temperature vs. resistance table, 4.90
trip temperatures
, 4.90
winding trip voting
, 4.90
Retrieve
event
, 3.11
Rotating Display
, 4.201
RTD
See Resistance Temperature Detector
S
Safety Information
Laser/LED Emitter
, xxxi
symbols
, xxv
SEL ASCII Protocol
, 7.16, C.1
SEL Binary Protocol
, C.2
SEL Communications Processor
, C.3–
C.10
SEL-2600 RTD Module
failure messages
, 5.6
fiber-optic connection, 2.25
RTD-based protection
, 4.89–4.90
SEL-3373
See Synchrophasors
SEL-751 Relay
cleaning chassis
, xxxiii
features
, 1.1
options
, 1.5
SEL
BOOT, 2.18
Self Tests
, 11.13
SEL
OGIC Control Equations, 4.160
circuit breaker auxiliary
, 4.130
contact output
, 4.168
counters
, 4.166
event trigger
operators
, 4.161–4.164
PMU trigger
, I.7
Relay Word bits
, K.1
timers
, 4.165
trip logic
, 4.129–4.131
Sequential Events Recorder (SER)
, 7.46,
10.37
clearing
, 10.37
example report
, 10.37
retrieving reports, 10.37
trigger settings
, 4.206, 10.37
SER
See Sequential Events Recorder
automatic deletion and reinsertion
,
4.205
SER D Command
, 7.47
SET Command
, 7.47
options
, 6.4
Set Relay
editing keystrokes
, 6.5
serial communications port, 6.4–6.6
using front panel
, 6.2
Settings
, 6.1–6.6
analog input example
, 4.181
classes, 6.1
error messages
, 6.6
front panel
, 6.2
Front-Panel (SET F Command),
4.193–4.204
Global (SET G Command)
, 4.169–
4.187
Group (SET Command)
, 4.3–4.185
Logic (SET L Command)
, 4.158
Modbus Map (SET M Command),
4.209
Port (SET P Command)
, 4.188
Report (SET R Command), 4.205
serial communications port
, 6.4–6.6
Short Circuit Protection
See Overcurrent Elements
SHOW command
, 6.4, 7.49
Side Panel
, 2.19
Simple Network Time Protocol (SNTP)
,
7.14
Software (
ACSELERATOR QuickSet), 3.1
databases
, 3.5
device editor, 3.9
expression builder
, 3.9
human machine interface (HMI)
, 3.13
settings editor, 3.6
Specifications
, 1.13
general
, 1.13–1.16
metering
, 1.19
processing specifications and
oscillography
, 1.17
relay elements
, 1.17
standards, compliance, 1.13
synchrophasor accuracy
, 1.20
type tests
, 1.16
Station DC Battery Monitor
, 5.15
Settings
, 5.15
undervoltage and overvoltage
elements
, 5.15
Status, Relay
, 7.51–7.52
serial communication port
DeviceNet status
, 1.11
serial communications port
, 1.11
Synchronism-Check Elements
, 4.106