MCE iControl - Page 614

iView - Controller View
9-136 Manual # 42-02-7223
• Hall Call Enable 1 (2) - Aux Front
• Hall Call Enable 1 (2) - Aux Front, Floor (1 - 96): Non-serial aux front inputs from Hall
call enable 1 (2) devices (card reader or keypad etc.).
• Hall Call Enable 1 (2) - Aux Rear
• Hall Call Enable 1 (2) - Aux Rear, Floor (1 - 96): Non-serial aux rear inputs from Hall
call enable 1 (2) devices (card reader or keypad etc.).
• Hall Call Enable 1 (2) - Aux Front Down
• Hall Call Enable 1 (2) - Down Aux Front, Floor (1 - 96): Non-serial down aux front
inputs from Hall call enable 1 (2) devices (card reader or keypad etc.).
• Hall Call Enable 1 (2) - Aux Rear Down
• Hall Call Enable 1 (2) - Down Aux Rear, Floor (1 - 96): Non-serial down aux rear inputs
from Hall call enable 1 (2) devices (card reader or keypad etc.).
• Hall Call Enable 1 (2) - Aux Rear Up
• Hall Call Enable 1 (2) - Up Aux Rear, Floor (1 - 96): Non-serial up aux rear inputs from
Hall call enable 1 (2) devices (card reader or keypad etc.).
• Hall Call Enable 1 (2) - Main Front Down
• Hall Call Enable 1 (2) - Down Main Front, Floor (1 - 96): Non-serial down main front
inputs from Hall call enable 1 (2) devices (card reader or keypad etc.).
• Hall Call Enable 1 (2) - Main Rear Down
• Hall Call Enable 1 (2) - Down Main Rear, Floor (1 - 96): Non-serial down main rear
inputs from Hall call enable 1 (2) devices (card reader or keypad etc.).
• Hall Call Enable 1 (2) - Main Front Up
• Hall Call Enable 1 (2) - Up Main Front, Floor (1 - 96): Non-serial up main front inputs
from Hall call enable 1 (2) devices (card reader or keypad etc.).
• Hall Call Enable 1 (2) - Main Rear Up
• Hall Call Enable 1 (2) - Up Main Rear, Floor (1 - 96): Non-serial up main rear inputs
from Hall call enable 1 (2) devices (card reader or keypad etc.).
• CFSS 1 (2) Enable 1 (2) - Floor
• CFSS 1 (2) Enable 1 (2) - Floor (1 - 96): Non-serial CFSS mode 1 (2) inputs from Hall
call enable 1 (2) devices (card reader or keypad etc.).
• CFSS 1 (2) Enable 1 (2) - Front
• CFSS 1 (2) Enable 1 (2) - Front, Floor (1 - 96): Non-serial CFSS mode 1 (2) front inputs
from Hall call enable 1 (2) devices (card reader or keypad etc.).
• CFSS 1 (2) Enable 1 (2) - Rear
• CFSS 1 (2) Enable 1 (2) - Rear, Floor (1 - 96): Non-serial CFSS mode 1 (2) rear inputs
from Hall call enable 1 (2) devices (card reader or keypad etc.).
• User Defined Events
• User Event (1 - 10): Activation of a User Event (1 - 10) input causes the corresponding
User Event (1 - 10) to be activated (Configuration > User-Defined Inputs tab).
• Heat Detectors
• Machine Room Heat Detectors: Signals that a machine room heat detector is activated.
• Hoistway Heat Detectors: Signals that a hoistway heat detector is activated.
• Heat Detectors Floor (1 - 96): Signals that a heat detector on floor (1 - 96) is activated.