2 Parameters
2.2 List of parameters
SINAMICS DCP
106 List Manual (LH21), 05/2016
Dependency: Refer to: r2110, r2114, r2122, r2124, r2125, r2134, r2145, r2146, r3121, r3123
Notice: The time comprises r2145 (days) and r2123 (milliseconds).
Note: The buffer parameters are cyclically updated in the background (refer to status signal in r2139).
The structure of the alarm buffer and the assignment of the indices is shown in r2122.
Description: Displays additional information about the active alarm (as integer number).
Dependency: Refer to: r2110, r2122, r2123, r2125, r2134, r2145, r2146, r3121, r3123
Note: The buffer parameters are cyclically updated in the background (refer to status signal in r2139).
The structure of the alarm buffer and the assignment of the indices is shown in r2122.
Description: Displays additional information about the active alarm (as integer number).
Dependency: Refer to: r2110, r2122, r2123, r2125, r2134, r2145, r2146, r3121, r3123
Note: The buffer parameters are cyclically updated in the background (refer to status signal in r2139).
The structure of the alarm buffer and the assignment of the indices is shown in r2122.
Description: Displays the system runtime in milliseconds when the alarm was cleared.
Dependency: Refer to: r2110, r2114, r2122, r2123, r2124, r2134, r2145, r2146, r3121, r3123
Notice: The time comprises r2146 (days) and r2125 (milliseconds).
Note: The buffer parameters are cyclically updated in the background (refer to status signal in r2139).
The structure of the alarm buffer and the assignment of the indices is shown in r2122.
Description: Displays the system runtime in milliseconds when the alarm was cleared.
Dependency: Refer to: r2110, r2114, r2122, r2123, r2124, r2134, r2145, r2146, r3121, r3123
Notice: The time comprises r2146 (days) and r2125 (milliseconds).
Note: The buffer parameters are cyclically updated in the background (refer to status signal in r2139).
The structure of the alarm buffer and the assignment of the indices is shown in r2122.
Description: Selects the faults for which the acknowledge mode is to be changed
r2124[0...63] Alarm value / Alarm value
CU_DCP, DCP_CTRL Can be changed: - Access level: 3
Data type: Integer32 Func. diagram: 8065
Min Max Factory setting
- - -
r2124[0...63] Alarm value / Alarm value
TM150, TM15DI_DO,
TM31
Can be changed: - Access level: 3
Data type: Integer32 Func. diagram: 8050, 8065
Min Max Factory setting
- - -
r2125[0...63] Alarm time removed in milliseconds / t_alarm res ms
CU_DCP, DCP_CTRL Can be changed: - Access level: 3
Data type: Unsigned32 Func. diagram: 8065
Min Max Factory setting
- [ms] - [ms] - [ms]
r2125[0...63] Alarm time removed in milliseconds / t_alarm res ms
TM150, TM15DI_DO,
TM31
Can be changed: - Access level: 3
Data type: Unsigned32 Func. diagram: 8050, 8065
Min Max Factory setting
- [ms] - [ms] - [ms]
p2126[0...19] Change acknowledge mode fault number / Chng ackn F_no
CU_DCP, DCP_CTRL Can be changed: U, T Access level: 3
Data type: Unsigned16 Func. diagram: 8075
Min Max Factory setting
0 65535 0
To Next Page
Loading...
