Siemens sinamics dcp - p50785 CUD digital input;output 4 output delay time; DI;DO 4 t_del_out; p50786 CUD digital input;output 5 output delay time; DI;DO 5 t_del_out; p50787 CUD digital input;output 6 output delay time; DI;DO 6 t_del_out; p50788 CUD digital input;output 7 output delay time; DI;DO 7 t_del_out

2 Parameters
2.2 List of parameters
SINAMICS DCP
256 List Manual (LH21), 05/2016
Dependency: The terminal must be set as an output (p50789[3] = 1).
Refer to: p50789
Note: DI/DO: bidirectional digital input/digital output
Description: Sets the delay time for digital input/output 4 (DI/DO 4, X177.15) on the CUD.
Dependency: The terminal must be set as an output (p50789[0] = 1).
Refer to: p50789
Note: DI/DO: bidirectional digital input/digital output
Description: Sets the delay time for digital input/output 5 (DI/DO 5, X177.16) on the CUD.
Dependency: The terminal must be set as an output (p50789[1] = 1).
Refer to: p50789
Note: DI/DO: bidirectional digital input/digital output
Description: Sets the delay time for digital input/output 6 (DI/DO 6, X177.17) on the CUD.
Dependency: The terminal must be set as an output (p50789[2] = 1).
Refer to: p50789
Note: DI/DO: bidirectional digital input/digital output
Description: Sets the delay time for digital input/output 7 (DI/DO 7, X177.18) on the CUD.
Dependency: The terminal must be set as an output (p50789[3] = 1).
Refer to: p50789
Note: DI/DO: bidirectional digital input/digital output
Description: Sets the type for digital input/output 4 ... 7 (DI/DO 4 ... DI/DO 7) of the CUD.
Value: 0: Input
1: Output
p50785 CUD digital input/output 4 output delay time / DI/DO 4 t_del_out
DCP_CTRL Can be changed: U, T Access level: 3
Data type: FloatingPoint32 Func. diagram: 2060
Min Max Factory setting
0 [ms] 10000 [ms] 0 [ms]
p50786 CUD digital input/output 5 output delay time / DI/DO 5 t_del_out
DCP_CTRL Can be changed: U, T Access level: 3
Data type: FloatingPoint32 Func. diagram: 2060
Min Max Factory setting
0 [ms] 10000 [ms] 0 [ms]
p50787 CUD digital input/output 6 output delay time / DI/DO 6 t_del_out
DCP_CTRL Can be changed: U, T Access level: 3
Data type: FloatingPoint32 Func. diagram: 2065
Min Max Factory setting
0 [ms] 10000 [ms] 0 [ms]
p50788 CUD digital input/output 7 output delay time / DI/DO 7 t_del_out
DCP_CTRL Can be changed: U, T Access level: 3
Data type: FloatingPoint32 Func. diagram: 2065
Min Max Factory setting
0 [ms] 10000 [ms] 0 [ms]
p50789[0...3] CUD digital input/output 4 ... 7 type / CUD DI/DO typ
DCP_CTRL Can be changed: T Access level: 3
Data type: Integer16 Func. diagram: 2060, 2065
Min Max Factory setting
0 1 0