Command groups
Table 2-21: Bus commands (cont.)
Command Description
BUS:B<x>:AUDio:WORDSel:POLarity Sets or queries the word select polarity for the specified AUDIO bus.
BUS:B<x>:AUDio:WORDSel:SOUrce Specifies the word select source waveform for the AUDIO bus.
BUS:B<x>:AUDio:WORDSel:THReshold Sets or queries the Audio Word Select source threshold for the specified bus.
BUS:B<x>:CAN:BITRate Sets or queries the CAN b it rate.
BUS:B<x>:CAN:BITRate:VALue Sets or queries CAN bit rate.
BUS:B<x>:CAN:FD:BITRate Sets or queries the increased data phase bit rate used by CAN FD packets on
the specified CAN bus.
BUS:B<x>:CAN:FD:BITRate:CUSTom Sets or queries the custom bit rate for the increased data phase of CAN FD
packets on the specified CAN bus.
BUS:B<x>:CAN:SAMPLEpoint Sets or queries the sample point for the specified CAN bus.
BUS:B<x>:CAN:SIGNal Sets or queries the signal type for the specified CAN bus.
BUS:B<x>:CAN:SOUrce Sets or queries the CAN source channel.
BUS:B<x>:CAN:STANDard Sets or queries which CAN standard specification to analyze the specified
CAN bus with.
BUS:B<x>:CAN:THReshold Sets or queries the source channel threshold for the specified CAN bus.
BUS:B<x>:DISplay:FORMat Sets or queries how the data is represented in the busform for the specified bus.
BUS:B<x>:DISplay:LAYout This command sets or queries the format a bus layer should use.
BUS:B<x>:ETHERnet:DATAMINUSTHRESHold Sets or queries the Ethernet DATA Minus source threshold for the specified bus.
BUS:B<x>:ETHERnet:DATAPLUSTHRESHold Sets or queries the Ethernet DATA Plus source threshold for the specified bus.
BUS:B<x>:ETHERnet:IPVFOUR Sets or queries whether IPV4 packets are available for triggering on Ethernet.
BUS:B<x>:ETHERnet:LOWTHRESHold Sets or queries the Ethernet DATA source Low threshold for the specified bus.
BUS:B<x>:ETHERnet:QTAGGING Sets or queries whether Q-Tagging packets are available for triggering o n
Ethernet.
BUS:B<x>:ETHERnet:SIGNALTYpe Sets or queries the Ethernet signal type for the specified bus.
BUS:B<x>:ETHERnet:SOUrce Specifies the Ethernet data source for differential input.
BUS:B<x>:ETHERNET:SOUrce:DMINus Sets or queries the Ethernet DMINus source.
BUS:B<x>:ETHERNET:SOUrce:DPLUs Sets or queries the Ethernet DPLUs source.
BUS:B<x>:ETHERnet:THRESHold Sets or queries the Ethernet DATA source High threshold for the specified bus.
BUS:B<x>:ETHERnet:TYPe Specifies the Ethernet standard type: 10Base-T or 100B ase-T.
BUS:B<x>:FLEXray:BITRate Sets or queries the FlexRay bus bit rate.
BUS:B<x>:FLEXray:BITRate:CUSTom Sets or queries the FlexRay custom bit rate for the specified bus.
BUS:B<x>:FLEXray:CHannel Sets or queries the FlexRay bus channel.
BUS:B<x>:FLEXray:LOWTHRESHold Sets or queries the FlexRay data source low threshold for the specified bus.
BUS:B<x>:FLEXray:SIGnal Sets or queries the FlexRay probe.
BUS:B<x>:FLEXray:SOUrce Sets or queries the FlexRay bus source.
BUS:B<x>:FLEXray:SOUrce:TXRX Sets or queries the FlexRay TxRx data source for the specified bus.
BUS:B<x>:FLEXray:THRESHold Sets or queries the FlexRay data source threshold for the specified bus.
BUS:B<x>:FLEXray:TXRXTHRESHold Sets or queries the FlexRay data source TxRx threshold for the specified bus.
MSO54, MSO56, MSO58, MSO58LP Programmer 2-15
To Next Page