Tektronix MSO58 - Page 83

Command groups
Table 2-37: Search and Mark commands (cont.)
Command
Description
SEARCH:SEARCH<x>:TRIGger:A:BUS:
FLEXRAY:DATa:QUALifier
Sets or queries the FlexRay bus search trigger data qualifier.
SEARCH:SEARCH<x>:TRIGger:A:BUS:
FLEXRAY:DATa:SIZe
Sets or queries the FlexRay bus search trigger data size.
SEARCH:SEARCH<x>:TRIGger:A:BUS:
FLEXRAY:EOFTYPE
Sets or queries the FlexRay bus search trigger end of file type.
SEARCH:SEARCH<x>:TRIGger:A:BUS:
FLEXRAY:ERRTYPE
Sets or queries the FlexRay bus search trigger error type.
SEARCH:SEARCH<x>:TRIGger:A:BUS:
FLEXray:FRAMEID:HIVALue
Sets or queries the high value when searching on a FlexRay bus frame id field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:
FLEXray:FRAMEID:QUALifier
Sets the qualifier to be used when searching on a FlexRay bus signal.
SEARCH:SEARCH<x>:TRIGger:A:BUS:
FLEXray:FRAMEID:VALue
Sets the low value when searching on a FlexRay bus id field.
SEARCH:SEARCH<x>:TRIGger:A:BUS:
FLEXray:FRAMEType
Sets or queries the FlexRay bus search trigger frame type.
SEARCH:SEARCH<x>:TRIGger:A:BUS:
FLEXRAY:HEADER:CRC
Sets or queries the FlexRay bus search trigger header CRC.
SEARCH:SEARCH<x>:TRIGger:A:BUS:
FLEXRAY:HEADER:CYCLECount
Sets or queries the FlexRay bus search trigger header cycle count.
SEARCH:SEARCH<x>:TRIGger:A:BUS:
FLEXRAY:HEADER:FRAMEID
Sets or queries the FlexRay bus search trigger header frame id.
SEARCH:SEARCH<x>:TRIGger:A:BUS:
FLEXRAY:HEADER:INDBits
Sets or queries the FlexRay bus search header Indicator Bits.
SEARCH:SEARCH<x>:TRIGger:A:BUS:
FLEXRAY:HEADER:PAYLENgth
Sets or queries the FlexRay bus search trigger header payload length.
SEARCH:SEARCH<x>:TRIGger:A:BUS:I2C:
ADDRess:MODe
Sets or queries the address mode for the specified I2C bus trigger search to
determine where to place a mark.
SEARCH:SEARCH<x>:TRIGger:A:BUS:I2C:
ADDRess:VALue
Sets or queries the address string when the search condition for the specified
search is Address or AddressData, to determine where to place a mark.
SEARCH:SEARCH<x>:TRIGger:A:BUS:I2C:
CONDition
Sets or queries the trigger condition for the specified I2C bus trigger search to
determine where to place a mark.
SEARCH:SEARCH<x>:TRIGger:A:BUS:I2C:
DATa:DIRection
Sets or queries the direction of the data for the I2C bus trigger search to determine
wheretoplaceamark.
SEARCH:SEARCH<x>:TRIGger:A:BUS:I2C:
DATa:SIZe
Sets or queries the length of the data string in bytes used for the specified I2C bus
trigger search to determine where to place a mark.
SEARCH:SEARCH<x>:TRIGger:A:BUS:I2C:
DATa:VALue
Sets or queries the data value of the data token for the specified I2C bus trigger
search to determine where to place a mark.
SEARCH:SEARCH<x>:TRIGger:A:BUS:LIN:
DATa:HIVALue
Specifies the high data value to be used in a LIN search.
SEARCH:SEARCH<x>:TRIGger:A:BUS:LIN:
DATa:QUALifier
Sets or queries the LIN bus search trigger data qualifier.
MSO54, MSO56, MSO58, MSO58LP Programmer 2-67