Agilent Technologies InfiniiVision 5000 Series Programmer's Guide

780 Agilent InfiniiVision 5000 Series Oscilloscopes Programmer's Guide
Index
fall time measurement, 272, 282
falling edge, 419
Fast Fourier Transform (FFT) functions, 230,
231, 242, 243, 244, 576
FF values in waveform data, 509
FFT (Fast Fourier Transform) functions, 230,
231, 242, 243, 244, 576
FFT (Fast Fourier Transform) operation, 237,
521
FFT math function, 168
fifty ohm impedance, disable setting, 396
FILename commands, 541
filename for hardcopy, 580
filename for recall, 352
filename for save, 359
filter for frequency reject, 442
filter for high frequency reject, 415
filter for noise reject, 418
filter used to limit bandwidth, 192, 220
filters to Fast Fourier Transforms, 244
fine horizontal adjustment (vernier), 407
fine vertical adjustment (vernier), 207
finish pending device operations, 108
first point displayed, 531
FLATtop window for amplitude
measurements, 244
format, 511, 516
FORMat commands, 541
format for block data, 107
format for generic video, 480, 484
format for hardcopy, 578, 581
format for image, 363
format for waveform data, 370
FormattedIO488 object, 45
formfeed for hardcopy, 246, 250
frame, 478
frame counters (CAN), error, 375
frame counters (CAN), overload, 376
frame counters (CAN), reset, 377
frame counters (CAN), total, 378
frame counters (UART), error, 386
frame counters (UART), reset, 387
frame counters (UART), Rx frames, 388
frame counters (UART), Tx frames, 389
framing, 473
FRAMing commands, 541
frequency measurement, 43, 272, 283
frequency resolution, 244
frequency span of display, 243
frequency versus dB, 230
front panel mode, 421
front panel Single key, 158
front panel Stop key, 160
front-panel lock, 395
full-scale horizontal time, 404, 409
full-scale vertical axis defined, 238
function, 162, 231, 232, 236, 237, 238, 239,
240, 242, 243, 244, 576, 577
FUNCtion commands, 228
function memory, 159
function turned on or off, 577
functions, 521
functions, erasing, 131
G
g(t) source, first input channel, 234
g(t) source, math operation, 233
g(t) source, second input channel, 235
gateway IP, 33
general trigger commands, 414
GENeric, 480, 484
generic video format, 480, 484
glitch duration, 451
glitch qualifier, 450
glitch source, 452
GLITch trigger commands, 445
glitch trigger duration, 446
glitch trigger polarity, 449
glitch trigger source, 446
GOFT commands, 542
GPIB interface, 33, 34
graphics, 211
graticule area for hardcopy print, 247
graticule area for saved image, 361
graticule colors, invert for hardcopy, 251, 583
graticule colors, invert for image, 364
graticule data, 211
grayscale palette for hardcopy, 253
grayscale palette for image, 365
grayscaling on hardcopy, 582
greater than qualifier, 450
greater than time, 434, 438, 446, 451
GREaterthan commands, 542
H
HANNing window for frequency
resolution, 244
hardcopy, 155, 246
HARDcopy commands, 245
hardcopy device, 579
hardcopy factors, 249, 362
hardcopy filename, 580
hardcopy format, 578, 581
hardcopy formfeed, 250
hardcopy grayscale, 582
hardcopy invert graticule colors, 251, 583
hardcopy layout, 252
hardcopy palette, 253
hardcopy print, area, 247
hardcopy printer driver, 584
hardware event condition register, 136
Hardware Event Condition Register
(:HWERegister:CONDition), 136
Hardware Event Condition Register
(:OPERegister:CONDition), 643
Hardware Event Enable Register
(HWEenable), 134
hardware event event register, 138
Hardware Event Event Register
(:HWERegister[:EVENt]), 138, 642
header, 660
high-frequency reject filter, 415, 442
high-resolution acquisition type, 164
hold until operation complete, 108
holdoff time, 416
holes in waveform data, 509
horizontal adjustment, fine (vernier), 407
horizontal position, 408
horizontal scale, 406, 410
horizontal scaling, 516
horizontal time, 404, 409, 587
hostname, 33
HWEenable (Hardware Event Enable
Register), 134
HWERegister:CONDition (Hardware Event
Condition Register), 136, 643
HWERegister[:EVENt] (Hardware Event Event
Register), 138, 642
I
I/O softkey, 33, 34
I1080L50HZ, 480, 484
I1080L60HZ, 480, 484
ID commands, 543
id mode, 427
identification number, 106
identification of options, 109
identifier, 426
identifier, LIN, 463
idle until operation complete, 108
IDN (Identification Number), 106
IEEE 488.2 standard, 99
IGColors commands, 543
IIC address, 454
IIC clock, 457
IIC commands, 543
IIC data, 455, 458
IIC data 2, 456
IIC serial decode address field size, 381
IIC trigger commands, 453
IIC trigger qualifier, 459
IIC trigger type, 460
IMAGe commands, 543
image format, 363
image invert graticule colors, 364
image memory, 159, 216
image palette, 365
image, recall, 353
image, save, 360
image, save with inksaver, 364
impedance, 195
IMPedance commands, 543
impedance for external trigger input, 221, 574
infinity representation, 677
initialization, 42, 45
initialize, 111
initialize label list, 214
initiate acquisition, 132
inksaver, save image with, 364
input, 221, 574
input coupling for channels, 193
input impedance for channels, 195, 570

Agilent Technologies InfiniiVision 5000 Series Specifications

General

Brand	Agilent Technologies
Model	InfiniiVision 5000 Series
Category	Test Equipment
Language	English