Agilent Technologies InfiniiVision 5000 Series Programmer's Guide

Index
Agilent InfiniiVision 5000 Series Oscilloscopes Programmer's Guide 781
input impedance for external trigger, 221, 574
input inversion for specified channel, 196
insert label, 197
installed options identified, 109
instruction header, 660
instrument number, 106
instrument options identified, 109
instrument requests service, 118
instrument serial number, 157
instrument settings, 246
instrument status, 52
instrument type, 106
integrate math function, 230, 237, 521
INTegrate source for function, 242, 576
INTERN files, 216
internal low-pass filter, 192, 220
introduction to :ACQuire commands, 163
introduction to :CALibrate commands, 179
introduction to :CHANnel commands, 190
introduction to :DISPlay commands, 208
introduction to :EXTernal commands, 218
introduction to :FUNCtion commands, 230
introduction to :HARDcopy commands, 246
introduction to :MARKer commands, 257
introduction to :MEASure commands, 272
introduction to :RECall commands, 351
introduction to :SAVE commands, 358
introduction to :SBUS commands, 374
introduction to :SYSTem commands, 391
introduction to :TIMebase commands, 400
introduction to :TRIGger commands, 411
introduction to :WAVeform commands, 502
introduction to common (*) commands, 99
introduction to root (:) commands, 124
invert graticule colors for hardcopy, 251, 583
invert graticule colors for image, 364
inverted masks, bind levels, 344
inverting input for channels, 196
IO library, referencing, 44
IP address, 33
IP Options softkey, 34
K
key disable, 395
key press detected in Standard Event Status
Register, 105
knob disable, 395
known state, 111
L
label, 568
LABel commands, 543
label list, 197, 214
labels, 197, 213, 214
labels to store calibration information, 182
labels, specifying, 208
LAN interface, 33, 36
LAN Settings softkey, 34
landscape layout for hardcopy, 252
language for program examples, 41
LaserJet, 579
layout for hardcopy, 252
leakage into peak spectrum, 244
learn string, 107, 397
least significant byte first, 507
left reference, 405
legal values for channel offset, 198
legal values for frequency span, 243
legal values for offset, 236, 239
LENGth commands, 544
length for waveform data, 371
less than qualifier, 450
less than time, 435, 438, 447, 451
LESSthan commands, 544
LEVel commands, 544
level for trigger voltage, 441, 448
LF coupling, 440
license information, 109
limits for line number, 480
LIN acknowledge, 464
LIN baud rate, 465
LIN identifier, 463
LIN serial decode bus parity bits, 382
LIN source, 466
LIN standard, 467
LIN sync break, 468
LIN trigger, 469
LIN trigger commands, 462
LIN trigger definition, 612
line glitch trigger source, 452
line number for TV trigger, 480
line terminator, 92
LINE trigger level, 441
LINE trigger source, 444
list of channel labels, 214
load utilization (CAN), 379
local lockout, 395
lock, 395
LOCK commands, 544
lock mask to signal, 335
lock, analog channel protection, 396
lockout message, 395
long form, 660
lower threshold, 287
lower threshold voltage for measurement, 585
lowercase characters in commands, 659
low-frequency reject filter, 442
low-pass filter used to limit bandwidth, 192,
220
LRN (Learn Device Setup), 107
lsbfirst, 507
M
magnitude of occurrence, 304
main sweep range, 408
main time base, 609
main time base mode, 402
making measurements, 272
MAN option for probe sense, 571, 575
manual cursor mode, 258
MARKer commands, 256
marker mode, 264
marker position, 265
marker readout, 591, 592
marker set for voltage measurement, 597, 598
marker sets start time, 588
marker time, 587
markers for delta voltage measurement, 596
markers track measurements, 296
markers, command overview, 257
markers, mode, 258
markers, time at start, 592
markers, time at stop, 591
markers, X delta, 263
markers, X1 position, 259
markers, X1Y1 source, 260
markers, X2 position, 261
markers, X2Y2 source, 262
markers, Y delta, 266
markers, Y1 position, 264
markers, Y2 position, 265
mask, 102, 115, 419, 436
MASK commands, 544
mask statistics, reset, 329
mask test commands, 318
Mask Test Event Enable Register
(MTEenable), 141
mask test event event register, 143
Mask Test Event Event Register
(:MTERegister[:EVENt]), 143, 644
mask test output, 336
mask test run mode, 337
mask test termination conditions, 337
mask test, enable/disable, 334
mask, delete, 333
mask, get as binary block data, 332
mask, load from binary block data, 332
mask, lock to signal, 335
mask, recall, 354
mask, save, 366
masks, bind levels, 344
master summary status bit, 118
math function, stop displaying, 130
math operations, 230
MAV (Message Available), 101, 116, 118
maximum duration, 434, 435, 447
maximum position, 403
maximum range for zoomed window, 409
maximum scale for zoomed window, 410
maximum vertical value measurement, 309
maximum vertical value, time of, 316, 589
MEASure commands, 267
measure overshoot, 285
measure period, 287
measure phase between channels, 288
measure preshoot, 289
measure start voltage, 597
measure stop voltage, 598
measure value at a specified time, 314
measure value at top of waveform, 315
measurement error, 272
measurement setup, 272, 297

Agilent Technologies InfiniiVision 5000 Series Specifications

General

Brand	Agilent Technologies
Model	InfiniiVision 5000 Series
Category	Test Equipment
Language	English