Index-7
DOOR LK CLIPPED G200 message 6-24
DOOR LK CLIPPED L200 message 6-24
Door Lock Clipped Greater than 200fpm message 6-24
Door Lock Clipped Less than 200fpm message 6-24
Door lock indicators 9-9
DOOR LOCK OPENED message 6-24
Door Motor Protection Timers
Closing 9-32
Opening 9-32
Door Open Button Bypass 9-32
Door Open Button Bypass Timer 9-32
Door Open delay timer to reverse closing doors 9-31
Door Opening Protection Timer 9-32
Door operator, preparing for final adjustments 3-28
Door parameters
verifying 3-24
Door pre-opening distance parameter 9-155
Door times 10-23
Door Zone 3-2
Door Zone Sensor (DZ) 3-12
Doors configuration 9-31–9-34
Doors Locked, iBox status LED 7-11
DOWN DIR LIMIT OPEN message 6-24
Down Direction Limit Open message 6-24
Down Emergency Switch Shutdown message 6-25
Down Emergency Terminal Switch Position Fault 6-24
DOWN ETS SHUTDOWN message 6-25
Down Level 3-2
Down Normal Terminal ’n’ Level 1 Speed Fault message 6-25
Down Normal Terminal ’n’ Level 2 Speed Fault message 6-25
Down Normal Terminal ’n’ Position Fault message 6-26
Down switch, iBox control 7-12
Down, iBox status LED 7-11
DP1-, Position Encoder input 6-109, 11-7
DP1+, Position Encoder input 6-109, 11-7
DP2-, Position Encoder input 6-109, 11-7
DP2+, Position Encoder input 6-109, 11-7
DPM, Door Position Monitor input 6-110, 11-8
Drawing Name 2-6
Drawing Number Format 2-6
Drive
Control tab 9-104
Dampening tab 9-112
Filters tab 9-108
Safety tab 9-102
Drive - Safety
Over Current parameters 9-103
Drive At Speed Fault message 6-26
drive auto tune procedure (Quattro DC) 2-74
Drive Calibration
calibrating offsets 9-168
Drive Communication Fault message 6-26
Drive Communication Warning message 6-26
Drive Configuration 9-99–9-115
General tab 9-100
Pre-Start Sequence parameters 9-100
Pre-Torque tab 9-114
Drive Connections, iBox 11-12
Drive Control Adjustments (Quattro DC Drive) 4-25
Drive Control parameters 9-104, 9-114
Pre-torque balance adjustment 9-114
Pre-torque gain 9-114
Pretorque position compensation 9-114
DRIVE ENABLE FDBK FLT message 6-26
Drive Enable Feedback Fault message 6-26
Drive Enable Status test point, description 11-4
Drive Fault, DRIVE FAULT message 6-27
Drive header current parameter 9-101
Drive header voltage parameter 9-101
Drive Inspection Overspeed Fault message 6-27
Drive interface parameter 9-100
DRIVE IOS FAULT message 6-27
Drive IOS Limit test point, description 11-4
Drive IOS Param Limit test point, description 11-4
Drive Offsets calibration parameters
Current Loop Integral 9-115
Current Sensor 9-115
Input ADC 9-115
Output DAC 9-115
Zero Crossing 9-115
Drive On, iBox status LED 7-11
Drive Parameters Quick Reference, Quattro 11-27
Drive Ready Fault message 6-27
Drive Ready On Fault message 6-27
drive response adjustments (Quattro DC) 2-75
Drive Start Failure message 6-27
Drive Startup (Quattro DC Drive) 2-71–2-85
Drive Startup (System 12 SCR Drive) 2-47–2-70
Drive Type parameter 9-100
Drive, diagnostic flags 9-13
Driver VDC 5-26
Drop delay, adjusting for final stop 4-33
Dual Channel QUAD Fault message 6-28
DUAL CHANNEL QUAD FLT message 6-28
Dynamic parking 10-22, 10-27
DZ, Door Zone Sensor input 6-110, 11-8
E
Earthquake (EQ) sensor 3-21
Earthquake board power supply OFF message 6-28
Earthquake board power supply ON message 6-28
Earthquake Board Quick Reference 6-94
Earthquake Buzzer output 9-139
Earthquake Code 9-68
Earthquake Emergency Stop message 6-28
Earthquake Light output 9-139
Earthquake Operation (Counterweight) message 6-28
Earthquake Operation (Seismic Switch) message 6-29
Earthquake Operation Activated message 6-28
Earthquake Operation Deactivated message 6-28
Earthquake parameters 9-68
Earthquake profile 4-19, 9-154
Earthquake Reduce Speed message 6-29
Earthquake reset button OK message 6-29
Earthquake reset button stuck ON message 6-29
Earthquake Run message 6-29
Earthquake Shutdown message 6-29
Edit a parameter on the iBox 7-5
Edit a parameter using iView 8-19
Editing a configuration file 8-23
To Next Page