Command groups
Table 2-37: Search and Mark commands (cont.)
Command
Description
SEARCH:SEARCH<x>:TRIGger:A:SETHold:
HOLDTime
Sets or queries the hold time setting for a setup/hold trigger search to determine
wheretoplaceamark.
SEARCH:SEARCH<x>:TRIGger:A:SETHold:
SETTime
Sets or queries the setup time setting for a setup/hold trigger search to determine
wheretoplaceamark.
SEARCH:SEARCH<x>:TRIGger:A:TIMEOut:
TIMe
Sets or queries the time setting for a timeout trigger search to determine where to
place a mark.
SEARCH:SEARCH<x>:TRIGger:A:
TRANsition:DELTATime
Sets or queries the transition time setting for a transition trigger search to determine
wheretoplaceamark.
SEARCH:SEARCH<x>:TRIGger:A:
TRANsition:WHEn
Sets or queries the condition setting for a transition trigger search to determine
wheretoplaceamark.
SEARCH:SEARCH<x>:TRIGger:A:TYPe Sets or queries the trigger type setting for a search to determine where to place
amark.
SEARCH:SEARCH<x>:TRIGger:A:WINdow:
WIDth
Sets or queries the width setting for a window search to determine where to place
amark.
SEARCH:SEARCH<x>:TRIGger:A:BUS:LIN:
CONDition
Sets or queries the LIN bus search trigger condition.
SEARCH:SEARCH<x>:TRIGger:A:BUS:USB:
DATa:QUALifier
Sets or queries the qualifier to be used when searching on a USB bus signal.
SEARCH:SEARCH<x>:TRIGger:A:EDG E:
THReshold
Sets or queries the source threshold level for an edge trigger search to determine
wheretoplaceamark.
SEARCH:SEARCH<x>:TRIGger:A:LOGIc:
CLOCk:THReshold
Sets or queries the logic clock threshold for a logic trigger search to determine
wheretoplaceamark.
SEARCH:SEARCH<x>:TRIGger:A:LOGIc:
DELTatime
Specifies the Logic search delta time value.
SEARCH:SEARCH<x>:TRIGger:A:LOGIc:
INPUT:CLOCK:SOUrce
Sets or queries the channel to use as the clock source for logic trigger.
SEARCH:SEARCH<x>:TRIGger:A:LOGIc:
LEVel:CH<x>
Sets or queries the voltage level to use for logic trigger search.
SEARCH:SEARCH<x>:TRIGger:A:LOGIc:
LEVel:MATH<x>
Sets the voltage level to use for logic trigger search.
SEARCH:SEARCH<x>:TRIGger:A:LOGIc:
LEVel:REF<x>
Sets the voltage level to use for logic trigger search.
SEARCH:SEARCH<x>:TRIGger:A:LOGIc:
LOGICPattern:CH<x>
Sets or queries the conditions used for generating an A logic pattern.
SEARCH:SEARCH<x>:TRIGger:A:LOGIc:
LOGICPattern:CH<x>_D<x>
Sets or queries the conditions used for generating an A logic pattern.
SEARCH:SEARCH<x>:TRIGger:A:LOGIc:
LOGICPattern:MAT H <x>
Sets or queries the conditions used for generating an A logic pattern.
SEARCH:SEARCH<x>:TRIGger:A:LOGIc:
LOGICPattern:REF<x>
Sets or queries the conditions used for generating an A logic pattern.
SEARCH:SEARCH<x>:TRIGger:A:LOGIc:
POLarity
Sets or queries the polarity for the clock channel when Use Clock Edge is set to Yes
for Logic search type.
MSO54, MSO56, MSO58, MSO58LP Programmer 2-71
To Next Page
Loading...
