Tektronix MSO58 - Page 88

Command groups
Table 2-37: Search and Mark commands (cont.)
Command
Description
SEARCH:SEARCH<x>:TRIGger:A:LOGIc:
WHEn
Sets or queries the condition for generating an A or B logic search with respect to
the defined input pattern.
SEARCH:SEARCH<x>:TRIGger:A:
PULSEWidth:HIGHLimit
Specifies the upper limit to use, in seconds, when searching for a pulse whose
duration is inside or outside a range of two values.
SEARCH:SEARCH<x>:TRIGger:A:
PULSEWidth:LOGICQUALification
Specifies whether or not to use logic qualification for a pulse width search.
SEARCH:SEARCH<x>:TRIGger:A:
PULSEWidth:LOWLimit
Specifies the lower limit to use, in seconds, when searching for a pulse whose
duration is inside or outside a range of two values.
SEARCH:SEARCH<x>:TRIGger:A:
PULSEWidth:POLarity
Specifies the polarity for a pulse width search.
SEARCH:SEARCH<x>:TRIGger:A:
PULSEWidth:SOUrce
Sets and queries the source for the pulsewidth search input.
SEARCH:SEARCH<x>:TRIGger:A:
PULSEWidth:THReshold
Sets or queries the source threshold level for a pulse width trigger search to
determine where to place a mark.
SEARCH:SEARCH<x>:TRIGger:A:
PULSEWidth:WHEn
Specifies to search for a pulse with a specified width.
SEARCH:SEARCH<x>:TRIGger:A:RUNT:
LOGICQUALification
Specifies whether or not to use logic qualification for a runt search.
SEARCH:SEARCH<x>:TRIGger:A:RUNT:
POLarity
Specifies the polarity for the runt search.
SEARCH:SEARCH<x>:TRIGger:A:RUNT:
SOUrce
Sets and queries the source for the Runt search input.
SEARCH:SEARCH<x>:TRIGger:A:RUNT:
THReshold:HIGH
Sets or queries the source threshold H IGH l evel for a runt trigger search to
determine where to place a mark.
SEARCH:SEARCH<x>:TRIGger:A:RUNT:
THReshold:LOW
Sets or queries the source threshold LO W level for a runt trigger search to
determine where to place a mark.
SEARCH:SEARCH<x>:TRIGger:A:SETHold:
CLOCk:THReshold
Sets or queries the clock threshold setting for a setup/hold trigger search to
determine where to place a mark.
SEARCH:SEARCH<x>:TRIGger:A:SETHold:
LEVel:CH<x>
Sets or queries the voltage level to u se for s etup & hold trigger search.
SEARCH:SEARCH<x>:TRIGger:A:SETHold:
LEVel:MATH<x>
Sets or queries the voltage level to u se for s etup & hold trigger search.
SEARCH:SEARCH<x>:TRIGger:A:SETHold:
LEVel:REF<x>
Sets or queries the voltage level to u se for s etup & hold trigger search.
SEARCH:SEARCH<x>:TRIGger:A:SETHold:
LOGICPattern:CH<x>
Sets or queries the conditions used for generating an A logic pattern.
SEARCH:SEARCH<x>:TRIGger:A:SETHold:
LOGICPattern:CH<x>_D<x>
Sets or queries the conditions used for generating an A logic pattern.
SEARCH:SEARCH<x>:TRIGger:A:SETHold:
LOGICPattern:MATH<x>
Sets or queries the conditions used for generating an A logic pattern.
SEARCH:SEARCH<x>:TRIGger:A:SETHold:
LOGICPattern:REF<x>
Sets and returns the conditions used for generating an A logic pattern.
2-72 MSO54, MSO56, MSO58, MSO58LP Programmer