Index-2 Manual # 42-02-7223
Alternate Speed Profile 1 input 9-128
Alternate Speed Profile 1 message 6-13
Alternate Speed Profile 2 Activated message 6-13
Alternate Speed Profile 2 Deactivated message 6-13
Alternate Speed Profile 2 input 9-128
Alternate Speed Profile 2 message 6-13
Anti-nuisance 9-42
Cancel car calls behind car 9-42
Light load 9-42
Photo Eye 9-42
Anti-nuisance controls 4-37
Approach deceleration parameter 4-18, 9-158
Approach jerk parameter 4-18, 9-158
Armature Active Status test point, description 11-3
Armature Command (Control) test point, description 11-3
Armature Command (Damped) test point, description 11-3
Armature Command (Raw) test point, description 11-3
Armature Composite Control test point, description 11-3
Armature Control Set test point, description 11-3
Armature Current 9-9
Dampening Speed 9-113
Dampening Torque 9-113
High-pass frequency 9-113
Low-pass frequency 9-113
Armature Current Dampen Feedback test point, 11-3
Armature Current Signal test point, description 11-3
Armature Current Synthetic Feedback test point, 11-3
Armature Current Test 9-105
Armature Differential Command test point, description 11-3
Armature Differential Gain test point, description 11-3
Armature Error (Damped) test point, description 11-4
Armature Error (Raw) test point, description 11-4
Armature Feedforward (Control) test point, description 11-4
Armature Feedforward (Raw) test point, description 11-4
Armature Integral Command test point, description 11-4
Armature Integral Gain test point, description 11-4
Armature On Status test point, description 11-4
Armature overcurrent overload protection (System 12) 4-48
Armature Proportional Command test point, description 11-4
Armature Proportional Gain test point, description 11-4
Armature Test 9-104
Armature Voltage 9-9
Dampening Speed 9-113
Dampening Torque 9-113
High-pass Frequency 9-113
Low-pass Frequency 9-113
Armature Voltage Dampen Feedback test point, 11-4
Armature Voltage Limit, setting for System 12 drive 4-7
Armature Voltage Signal (System 12) 4-10
Armature Voltage Signal test point, description 11-4
Armature Voltage Synthetic Feedback test point, 11-4
Arrival Fixtures, parameters 9-35
Ascending Car Overspeed Fault message 6-13
ASCND CAR OVR SPD FLT message 6-13
ATD, Hoistway Access Top Down switch input 6-111, 11-10
Attendant Buzzer output 9-137
Attendant HC Above output 9-137
Attendant HC Below output 9-137
Attendant Service Down input 9-128
Attendant Service Indicator output 9-137
Attendant Service input 9-128
Attendant Service message 6-13
Attendant Service mode 9-4
Attendant Service Non-Stop input 9-128
Attendant Service parameters 9-82
Attendant Service Up input 9-128
Attendant Svc message 6-13
ATU, Hoistway Access Top Up switch input 6-111, 11-10
Auto Stop parameters 9-83
automated drive setup (Quattro DC) 2-73
Automatic 10-83
Automatic mode, selecting 10-16
Automatic Stop Input 9-128
Automatic Stop message 6-13
Automatic Swing Operation 9-43
Available for fire service output 9-137
Average wait times 10-87
B
B-, Velocity Encoder input 6-109, 11-7
B+, Velocity Encoder input 6-109, 11-7
B1, B2, DC power to motor brake 11-14
Backup Dispatcher, description of 10-4
Backup power direction reversal message 6-13
Backup power recall done output 9-137
Backup power recall input 9-128
BACKUP POWER RECALL message 6-14
Backup power recall OFF message 6-14
Backup power recall ON message 6-14
Backup power recall reverse direction input 9-128
Backup power unit failure activated message 6-14
Backup power unit failure deactivated message 6-14
Backup power unit failure input 9-128
Backup power unit failure message 6-14
Balanced 10-83
Balanced Mode message 6-14
Balanced mode, selecting 10-16
Balancing the Counterweight 3-29
BATTERY VLTG LOW-IMP message 6-14
Battery Voltage Low-IMP message 6-14
BD, Brake Drive relay indicator 11-12
BDRD, Brake Drive Redundancy indicator 11-12
Blocking New Remote Connections message 6-14
BLOCKING REMOTE UIS message 6-14
Blue cables 5-12, 5-13
Boot parameter recovery utility 8-49
Brake
adjust to control rollback (Quattro DC) 2-77
auto calibration procedure (Quattro DC) 2-78
Brake monitoring 3-20
calibration 9-166
configuration 9-25–9-28
Current Reference 9-28
current, on Operational Status tab 9-9
Filters 9-26
iBox connections 11-12
Output Timer 9-28
Resistance 2-22
setup 9-166
Timers 9-27
To Next Page
Loading...
Need help?
General