MCE iControl User Manual

Index-1
Index
Numerics
1 = LAN port 2-5
1 bus, Common bus connections 11-13, 11-14
110 VDC Bus Connections, iBox 11-13
120 VAC Bus Connections, iBox 11-13
15A, Final Limit switch connection 11-14
15B, Pit/Final Limit switch connection 11-14
2 = System port 2-5
2 bus, 120 VAC connections 11-13, 11-14
2 PI bus, 120 VAC connections 11-13
3 = PC port 2-5
3 = PC port connections 2-35
3 bus, 110 VDC connections 11-13, 11-14
3 HA bus, 110 VDC connections 11-13
A
A-, Velocity Encoder input 6-109, 11-7
A+, Velocity Encoder input 6-109, 11-7
ABD, Hoistway Access Bottom Down switch input 6-111, 11-10
ABU, Hoistway Access Bottom Up switch input 6-111, 11-10
AC supply 5-7
Acceleration (Command) test point, description 11-3
Acceleration (Directional) test point, description 11-3
Acceleration (Filtered) test point, description 11-3
Acceleration (Interpolated) test point, description 11-3
Acceleration (Raw) test point, description 11-3
Acceleration (Slew) test point, description 11-3
Acceleration parameter 4-18, 9-158
Acceleration specification 11-2
accessing online help 8-24
Acquired floor marker heights mismatch configuration 9-172
Acquired floor markers fewer than configuration 9-172
Acquired floor markers more than configuration 9-172
Acquiring floor markers 9-172
acquiring write privilege 2-30
Active configuration serial outputs 10-64
Active configurations, setting 9-121
Active Mode - Balanced output 9-146
Active Mode - Demand Down Peak output 9-146
Active Mode - Demand Up Peak output 9-146
Active Mode of Operation Outputs 10-67
Actual direction 9-8
Actual Position 9-8
Actual speed, calibrating (Quattro DC) 2-82
ADA Car Call Dwell Time 9-45
ADA Hall Call Dwell Time 9-45
ADC, verifying ADC conversion 2-49
Add a timer 9-162, 10-71
Adding a circuit board 6-80
Adjusting
Brake coordination 4-33
Brake drop delay 4-31
Brake parameters 4-25
Brake Resistance 2-22
Counterweight Balance 3-29
Dead zone 4-32
Emergency slowdown 4-55
Final Approach 4-31
Final approach 4-20
Leveling speed 4-31
Load thresholds 4-37
Load Weigher 4-36, 4-38
overshoot 4-19
Overspeed Margins 4-57
Pattern parameters 4-19
Pretorque 4-21
Releveling 4-34
Ride quality 4-35
System 12 Drive 2-49
Tachometer Error tripping threshold 4-47
adjusting car speed (Quattro DC) 2-82
Alarm Button input 9-128
Alarm Buzzer 9-36
Alarm Buzzer output 9-137
Alarm Light 9-36
Alarm Light output 9-137
Alarm Reset input 9-128
Allow floor hall calls to reverse doors on a departing car 10-12
ALT SPEED PROFILE 1 message 6-13
ALT SPEED PROFILE 2 message 6-13
Alternate 1 profile 4-19, 9-154
Alternate 2 profile 4-19, 9-154
Alternate Dispatcher selection 10-8
Alternate Fire Switch ON input 9-128
Alternate Floor Smoke input 9-128
ALTERNATE FLOOR SMOKE message 6-13
Alternate Floor Smoke Sensor Recall message 6-13
Alternate Recall floor, Fire service 9-48
Alternate Speed Profile 1 Activated message 6-13
Alternate Speed Profile 1 Deactivated message 6-13

MCE iControl Specifications

General

Brand	MCE
Model	iControl
Category	Controller
Language	English