Agilent Technologies InfiniiVision 5000 Series Programmer's Guide

786 Agilent InfiniiVision 5000 Series Oscilloscopes Programmer's Guide
Index
trigger, glitch polarity, 449
trigger, glitch qualifier, 450
trigger, glitch range, 451
trigger, glitch source, 452
trigger, high frequency reject filter, 415
trigger, holdoff, 416
trigger, IIC clock source, 457
trigger, IIC data source, 458
trigger, IIC pattern address, 454
trigger, IIC pattern data, 455
trigger, IIC pattern data 2, 456
trigger, IIC qualifier, 459
trigger, IIC signal baudrate, 465
trigger, IIC type, 460
trigger, LIN, 469
trigger, LIN sample point, 464
trigger, LIN signal definition, 612
trigger, LIN source, 466
trigger, mode, 417
trigger, noise reject filter, 418
trigger, pattern, 419
trigger, SPI clock slope, 471
trigger, SPI clock source, 476
trigger, SPI clock timeout, 472
trigger, SPI data source, 477
trigger, SPI frame source, 478
trigger, SPI framing, 473
trigger, SPI pattern data, 474
trigger, SPI pattern width, 475
trigger, sweep, 421
trigger, TV line, 480
trigger, TV mode, 481, 613
trigger, TV polarity, 482
trigger, TV source, 483
trigger, TV standard, 484
trigger, UART base, 487
trigger, UART baudrate, 488
trigger, UART bit order, 489
trigger, UART parity, 493
trigger, UART polarity, 494
trigger, UART Rx source, 496
trigger, UART Tx source, 497
trigger, UART width, 499
truncation rules, 660
TST (Self Test), 120
tstart, 591
tstop, 592
turn function on or off, 577
turn off channel, 130
turn off channel labels, 213
turn off cursors, 126
turn off digital pod, 130
turn off math function, 130
turn off measurements, 126
turn off trace memories, 126
turn off zoomed time base mode, 126
turn on channel labels, 213
turn on channels, 126
turning channel display on and off, 194
turning off/on function calculation, 232
turning vectors on or off, 572
TV mode, 481, 613
TV trigger commands, 479
TV trigger line number setting, 480
TV trigger mode, 483
TV trigger polarity, 482
TV trigger standard setting, 484
TV triggering, 411
tvmode, 613
Tx data, UART, 525
Tx frame count (UART), 389
Tx source, 497
type, 177, 526
TYPE commands, 558
U
UART base, 487
UART baud rate, 488
UART bit order, 489
UART commands, 558
UART frame counters, reset, 387
UART parity, 493
UART polarity, 494
UART Rx source, 496
UART trigger burst, 490
UART trigger commands, 485
UART trigger data, 491
UART trigger idle, 492
UART trigger qualifier, 495
UART trigger type, 498
UART Tx data, 525
UART Tx source, 497
UART width, 499
UNITs commands, 559
units per division, 205, 206, 227, 406
units per division (vertical) for function, 205,
240
units, automask, 325
unsigned mode, 527
upper threshold, 287
upper threshold voltage for measurement, 595
uppercase characters in commands, 659
URQ (User Request) status bit, 103, 105
USB (Device) interface, 33
user defined channel labels, 197
user event conditions occurred, 118
User's Guide, 4
USR (User Event bit), 116, 118
Utility button, 33, 34
utilization, CAN bus, 379
V
valid command strings, 659
valid pattern time, 434, 435
value, 304
value measured at base of waveform, 308
value measured at specified time, 314
value measured at top of waveform, 315
value ranges, 93
values required to fill time buckets, 167
VBA, 44, 744
vectors, 217
vectors turned on or off, 572
vectors, turning on or off, 208
vernier, channel, 207
vernier, horizontal, 407
vertical adjustment, fine (vernier), 207
vertical amplitude measurement, 306
vertical axis defined by RANGe, 238
vertical axis range for channels, 204
vertical offset for channels, 198
vertical peak-to-peak measured on
waveform, 311
vertical scale, 205, 240
vertical scaling, 516
vertical value at center screen, 236, 239
vertical value maximum measured on
waveform, 309
vertical value measurements to calculate
overshoot, 285
vertical value minimum measured on
waveform, 310
video line to trigger on, 480
video standard selection, 484
view, 162, 230, 528
view turns function on or off, 577
VISA COM example in C#, 754
VISA COM example in Visual Basic, 744
VISA COM example in Visual Basic .NET, 765
VISA example in C, 698
VISA example in C#, 717
VISA example in Visual Basic, 707
VISA example in Visual Basic .NET, 731
VISA examples, 698, 744
Visual Basic .NET, VISA COM example, 765
Visual Basic .NET, VISA example, 731
Visual Basic 6.0, 45
Visual Basic for Applications, 44, 744
Visual Basic, SICL library example, 689
Visual Basic, VISA COM example, 744
Visual Basic, VISA example, 707
voltage crossing reported or not found, 593
voltage difference between data points, 532
voltage difference measured, 596
voltage level for active trigger, 441
voltage marker used to measure
waveform, 597, 598
voltage offset value for channels, 198
voltage probe, 206, 227
voltage ranges for channels, 204
voltage ranges for external trigger, 226
voltage threshold, 277
W
WAI (Wait To Continue), 121
wait, 121
wait for operation complete, 108
Wait Trig bit, 147, 149
waveform base value measured, 308
WAVeform command, 43
WAVeform commands, 500, 560
waveform data, 502

Agilent Technologies InfiniiVision 5000 Series Specifications

General

Brand	Agilent Technologies
Model	InfiniiVision 5000 Series
Category	Test Equipment
Language	English