Index-15
Local Dispatcher, description of 10-4
Locked, Security status 10-48, 10-51
Locks/Contacts Connections, iBox 6-112, 11-11
Logical Position 9-8
Loop over-current fault time parameter 4-49, 9-103
Loop over-current fault time parameter adjustment 4-49
LOSS OF POS/SPD IND message 6-53
Loss of Position or Speed Indicators message 6-53
Low roll jerk parameter 4-18, 9-158
Low speed parameter 9-158
M
MAC ADDRESS ERROR message 6-53
Mac Address Error message 6-53
MAC addresses 9-148
viewing on iBox 7-8
Mach Rm Insp message 6-54
Machine mode 9-8
Machine Rm Inspection message 6-54
Machine Room Heat Detectors Activated message 6-54
Machine Room Heat Detectors Deactivated message 6-54
Machine Room Inspection Disabled message 6-54
Machine Room Inspection Enabled message 6-54
Machine Room Inspection mode 9-5
Machine Room Inspection Operation message 6-54
Machine Room Inspection output 9-141
Machine Room Inspection switch 7-12
Machine Room Inspection, running on 3-26
Machine Room Preparation
Equipment location 2-4
Machine Room Stop Switch Open message 6-54
Main Fire Recall floor 9-48
Main Floor Smoke input 9-130
MAIN FLOOR SMOKE message 6-54
Main Floor Smoke Sensor Recall message 6-54
Main Processor Board Quick Reference 6-96
Manual configuration serial inputs 10-64
Master Security Override input 9-134
Maximum Full Load Output Current 4-8
Maximum open time 9-96
MCE 5-18
MCE job number parameter 10-7
MCE Load Weigher 5-61–5-67
adjusting 5-66
installation 5-61
maintaining 5-66
wiring 5-65
MCE Load Weigher. See also Load Weigher
MCE Loadweigher-Isolated Platform 3-19
MCE System hub 5-10, 5-12
MD, Motor Drive relay indicator 11-12
MDRD, Motor Drive Redundancy indicator 11-12
Mechanical Safe Edge 9-31
Mechanically In Service output 9-141
Melina PI display Outputs 9-145
Menu Bar 8-17
Menu tree, iBox LCD display 7-6
MF FORCING TIMED OUT message 6-55
MF1, MF2, DC power to motor field 11-14
Minimum Floor to Floor Time specification 11-2
Mode of Operation 5-26, 9-4, 10-15
Mode of Operation Config inputs 9-134
Mode of Operation Config outputs 9-146
monitoring Diagnostic Outputs 9-14
Motion
Actual direction 9-8
Category 9-8
Commanded direction 9-8
Motion Start Fault message 6-55
Motion stopped due to IO toggle test message 6-55
MOTION STOPPED-IO TST message 6-55
Motion, diagnostic flags 9-13
Motor blower hold delay parameter 9-100
Motor Blower output 9-145
MOTOR CNTR PROOF FLT message 6-55
Motor Contactor Driver Proofing Fault message 6-55
Motor Contactor Proofing Fault message 6-55
Motor Contactor Status test point, description 11-5
Motor Control Adjustments (System 12 SCR Drive) 4-24
Motor Field calibration 9-174
Motor Field Configuration
Configuration tab 9-153
Control 9-151
Motor Field Configuration parameters 9-151
Motor field current low pass frequency parameter 9-152
Motor field filters 9-152
Motor Field Forcing Timed Out message 6-55
Motor Field gains, manually adjusting (system 12) 2-56
Motor Field Options, Field Operation 9-151
Motor field voltage low pass frequency parameter 9-152
Motor Field, adjusting for System 12 drive 4-8
Motor insulation 2-21
Motor Limit Protection Timer Elapsed message 6-55
MOTOR LIMIT TIMED OUT message 6-55
Motor Limit Timed Out message 6-55
MOTOR LMT TIMED OUT 2 message 6-55
Motor Noise 4-20
motor rotation and control, verifying (Quattro DC) 2-81
Motor Triac active indicator 11-12
MOTR CNTR DRV PRF FLT message 6-55
Move idle car penalty 10-12
Move lobby parked car penalty 10-12
Move non-lobby parked car penalty 10-12
MR HEAT DETECTORS message 6-54
MR INSP. DISABLED message 6-54
MR STOP SWITCH OPEN message 6-54
MRD, Motor Redundancy indicator 11-12
Multiple Input AC Board Quick Reference 6-103
Multiple Output Relay Board Quick Reference 6-105
To Next Page