Agilent Technologies InfiniiVision 5000 Series Programmer's Guide

Index
Agilent InfiniiVision 5000 Series Oscilloscopes Programmer's Guide 783
P
P1080L24HZ, 480, 484
P1080L25HZ, 480, 484
P480L60HZ, 480, 484
P720L60HZ, 480, 484
PAL, 480, 484
PALette commands, 548
palette for hardcopy, 253
palette for image, 365
PAL-M, 480, 484
parameters for delay measurement, 279
parametric measurements, 272
parity, 493
parity bits, LIN serial decode bus, 382
PARity commands, 548
parser, 124, 675
pass (mask test) output, 336
pass, self test, 120
path information, recall, 355
path information, save, 367
pattern, 419, 424, 426, 436, 454, 455, 456,
474
pattern and edge, 419
PATTern commands, 548
pattern duration, 434, 435, 446, 447
pattern length, 425
pattern trigger, 419
pattern triggering, 411
pattern width, 475
peak detect, 177
peak detect acquisition type, 164, 502
peaks, 230
peak-to-peak vertical value measurement, 311
pending operations, 108
percent of waveform overshoot, 285
percent thresholds, 277
period measured to calculate phase, 288
period measurement, 43, 272, 287
persistence, waveform, 208, 215
phase measured between channels, 288
phase measurements, 302
pixel memory, 216
pixel memory, saving display to, 140
PLL Locked bit, 136, 147
pod, 521
pod, stop displaying, 130
points, 170, 512, 514
POINts commands, 549
points in waveform data, 502
polarity, 482, 494
POLarity commands, 549
polarity for glitch trigger, 449
polling synchronization with timeout, 650
polling wait, 648
PON (Power On) status bit, 103, 105
portrait layout for hardcopy, 252
position, 261, 403, 408
POSition commands, 549
position cursors, 591, 592
position in zoomed view, 408
positive glitch trigger polarity, 449
positive pulse width, 290
positive pulse width measurement, 43
positive slope, 443, 471
positive TV trigger polarity, 482
positive width, 290
preamble data, 502, 516
present working directory, recall
operations, 355
present working directory, save operations, 367
preset conditions, 111
preshoot measured on waveform, 289
previously stored configuration, 110
print command, 155
print job, start, 255
print mask test failures, 338
print query, 607
printer, 579
printer driver for hardcopy, 584
printer hardcopy format, 581
printer, active, 248
printing, 246
printing in grayscale, 582
probe, 441
probe attenuation affects channel voltage
range, 204
probe attenuation factor (external trigger), 222
probe attenuation factor for selected
channel, 199
PROBe commands, 549
probe ID, 200, 223
probe sense for oscilloscope, 571, 575
probe skew value, 201, 569
process sigma, mask test run, 341
program data, 660
program data syntax rules, 662
program initialization, 42
program message, 45, 99
program message syntax, 659
program message terminator, 660
program structure, 42
programming examples, 4, 679
protecting against calibration, 186
protection, 151, 153, 203, 225
PROTection commands, 549
protection lock, 396
pulse width, 284, 290
pulse width duration trigger, 446, 447, 451
pulse width measurement, 43, 272
pulse width trigger, 418
pulse width trigger level, 448
pulse width triggering, 411
PWD commands, 549
pwidth, 290
Q
qualifier, 451
QUALifier commands, 549
qualifier, trigger duration, 434, 435, 437
queries, multiple, 51
query error detected in Standard Event
Status, 105
query responses, block data, 50
query responses, reading, 49
query results, reading into numeric
variables, 50
query results, reading into string variables, 50
query return values, 677
query setup, 246, 257, 272, 397
query subsystem, 230
querying setup, 190
querying the subsystem, 411
queues, clearing, 645
quick reference, commands, 55
quoted ASCII string, 93
QYE (Query Error) status bit, 103, 105
R
range, 230, 409
RANGe commands, 550
range for channels, 204
range for duration trigger, 438
range for external trigger, 226
range for full-scale vertical axis, 238
range for glitch trigger, 451
range for time base, 404
range of offset values, 198
range qualifier, 450
ranges, value, 93
rate, 176
ratio of AC RMS values measured between
channels, 312
RCL (Recall), 110
read configuration, 107
read trace memory, 211
ReadIEEEBlock method, 45, 49, 51
ReadList method, 45, 49
ReadNumber method, 45, 49
readout, 587
ReadString method, 45, 49
real-time acquisition mode, 164, 169
recall, 110, 351, 397
RECall commands, 351
recall filename, 352
recall image, 353
recall mask, 354
recall path information, 355
recall setup, 356
recalling and saving data, 208
RECTangular window for transient signals, 244
reference, 230, 405
REFerence commands, 550
reference for time base, 609
registers, 104, 110, 114, 125, 134, 136, 138,
141, 143, 145, 147, 149, 151, 153
registers, clearing, 645
reject filter, 442
reject high frequency, 415
reject noise, 418
remote control examples, 679
remove cursor information, 258
remove labels, 213
remove message from display, 393

Agilent Technologies InfiniiVision 5000 Series Specifications

General

Brand	Agilent Technologies
Model	InfiniiVision 5000 Series
Category	Test Equipment
Language	English