Agilent Technologies InfiniiVision 5000 Series Programmer's Guide

784 Agilent InfiniiVision 5000 Series Oscilloscopes Programmer's Guide
Index
reorder channels, 126
repetitive acquisitions, 156
report errors, 394
report transition, 302, 304
reporting status, 623
reporting the setup, 411
request service, 118
Request-for-OPC flag clear, 101
reset, 111
RESet commands, 550
reset conditions, 111
reset mask statistics, 329
reset measurements, 131, 210
resolution of printed copy, 582
resource session object, 45
ResourceManager object, 45
restore configurations, 107, 110, 114, 397
restore labels, 213
restore setup, 110
return values, query, 677
returning acquisition type, 177
returning number of data points, 170
right reference, 405
rise time measurement, 272
rise time of positive edge, 294
rising edge, 419
RMODe commands, 550
RMS value measurement, 313
roll time base mode, 402
root (:) commands, 122, 124
root level commands, 96
RQL (Request Control) status bit, 103, 105
RQS (Request Service), 118
RST (Reset), 111
rules, tree traversal, 675
rules, truncation, 660
RUMode commands, 551
run, 119, 156
Run bit, 147, 149
run mode, mask test, 337
running configuration, 114, 397
Rx frame count (UART), 388
Rx source, 496
S
sample rate, 176
sampled data, 572
sampled data points, 509
SAMPlepoint commands, 551
SAV (Save), 114
save, 114, 358
SAVE commands, 357, 551
save filename, 359
save image, 360
save image with inksaver, 364
save mask, 366
save mask test failures, 339
save path information, 367
save setup, 368
SAVE TO INTERN, 140
save waveform data, 369
save waveforms to pixel memory, 140
saved image, area, 361
saving and recalling data, 208
SBUS commands, 373
scale, 240, 406, 410
SCALe commands, 552
scale factors output on hardcopy, 249, 362
scale for channels, 205
scale units for channels, 206
scale units for external trigger, 227
scaling display factors, 199
SCPI commands, 53
scratch measurements, 586
screen area for hardcopy print, 247
screen area for saved image, 361
screen data, 211
SECAM, 480, 484
seconds per division, 406
SEGMented commands, 552
segmented waveform save option, 372
segments, analyze, 171
segments, count of waveform, 519
segments, setting number of memory, 172
segments, setting the index, 173
segments, time tag, 520
select measurement channel, 297
self-test, 120
sensing a channel probe, 571
sensing a external trigger probe, 575
sensitivity of oscilloscope input, 199
sequence triggering, 411
sequential commands, 678
serial clock, 457, 476
serial data, 458, 477
serial decode bus, 374
serial decode bus display, 380
serial decode mode, 383
serial frame, 478
serial number, 157
service request, 118
Service Request Enable Register (SRE), 116,
631
set, 111
set center frequency, 231
set conditions, 126
set cursors, 591, 592
set date, 392
set delay, 126
set thresholds, 126
set time, 399
set time/div, 126
set up oscilloscope, 33
setting display, 232
setting external trigger level, 218
setting impedance for channels, 195
setting inversion for channels, 196
settings, 110, 114
settings, instrument, 246
setup, 164, 190, 208, 230, 246, 397
SETup commands, 552
setup configuration, 110, 114, 397
setup defaults, 111
setup memory, 110
setup reported, 411
setup, recall, 356
setup, save, 368
short form, 3, 660
show channel labels, 213
show measurements, 272, 296
SICL example in C, 680
SICL example in Visual Basic, 689
SICL examples, 680
sigma, mask test run, 341
SIGNal commands, 553
signal type, 202, 224
simple command headers, 661
single acquisition, 158
single-ended signal type, 202, 224
single-shot DUT, synchronizing with, 652
skew, 201, 569
slope, 443, 471
slope (direction) of waveform, 593
SLOPe commands, 553
slope not valid in TV trigger mode, 443
slope parameter for delay measurement, 279
software version, 106
source, 216, 230, 297, 430, 466, 521
SOURce commands, 553
source for function, 241, 242, 576
source for trigger, 444
source for TV trigger, 483
source, automask, 324
source, mask test, 349
SOURce1 commands, 553
SOURce2 commands, 553
span, 230
span of frequency on display, 243
specify measurement, 297
SPI, 471, 472, 474
SPI commands, 554
SPI decode word width, 384
SPI trigger, 473, 475
SPI trigger clock, 476
SPI trigger commands, 470
SPI trigger data, 477
SPI trigger frame, 478
square root math function, 237
SRE (Service Request Enable Register), 116,
631
SRQ (Service Request interrupt), 134, 141, 145
STANdard commands, 554
standard deviation measured on
waveform, 295
Standard Event Status Enable Register
(ESE), 102, 636
Standard Event Status Register (ESR), 104, 635
standard for video, 484
standard, LIN, 467
start acquisition, 119, 132, 156, 158
start and stop edges, 277
STARt commands, 554
start cursor, 591
start measurement, 272
start print job, 255

Agilent Technologies InfiniiVision 5000 Series Specifications

General

Brand	Agilent Technologies
Model	InfiniiVision 5000 Series
Category	Test Equipment
Language	English