Index-5
CFSS Mode 1 (2) at Floor mode 9-4
CFSS Mode 1 (2) In-car mode 9-4
CFSS Mode 1 (2) In-Use outputs 9-138
CFSS Mode 1 (2) Recall mode 9-4
CFSS Mode 1 (2) System outputs 9-138
CFSS Mode 1 at Floor Activated message 6-22
CFSS Mode 1 In-car Activated message 6-22
CFSS Mode 1 Recall Activated message 6-22
CFSS Mode 2 at Floor Activated message 6-22
CFSS Mode 2 In-car Activated message 6-22
CFSS Mode 2 Recall Activated message 6-22
CFSS operation 10-9
CFSS Recall 9-78
In-car audible indicator 9-78
In-car visual indicator 9-78
CFSS serial outputs 10-61
CFSS System 1 (2) outputs 9-146
CFSS tab 10-9
Changing parameters 2-30
Check for shorts to ground 2-16
Checking AC phase 5-7
Checking the Hoist Motor 2-21
Circuit board removing & replacing 6-80
Circuit boards, troubleshooting 6-81–6-117
Clone Controller Data 7-8
CNPB Fault, see Brake Contactor Proofing Fault message 6-14
CNPBD Fault, see Brake Contactor Driver Proofing Fault
message 6-14
CNPM Fault, see Motor Contactor Proofing Fault 6-55
CNPMD Fault, see Motor Contactor Driver Proof Fault 6-55
Cnstr Car Panel Insp message 6-22
Cnstr Cartop Insp message 6-23
Cnstr CP Insp message 6-22
Cnstr CT Insp message 6-23
Cnstr HA Insp message 6-23
Cnstr HA Inspection message 6-23
Cnstr Inspection message 6-23
Cnstr Mach Room Insp message 6-23
Cnstr MR Insp message 6-23
Coincidence call bonus 10-12
Commanded direction 9-8
Commandeer For Special Service 9-77–9-80, 10-9
Commercial Power output 9-138
Common Bus Connections, iBox 11-13
Computer IP address, setting 2-35–2-38, 8-5
Computer Reset, iBox control 7-4
Computer, iBox status LED 7-11
Configuration 9-25–9-163
Brake 9-25
Car Call Enable 9-29
Car Operation 9-30
Drive 9-99
Floor heights 9-116
General tab 9-117
I/O Boards 9-122
Load weigher tab 9-149
Motor Field 9-151
Pattern 9-154
Serial I/O 10-59
Terminal switches 9-160
Configuration File 6-78
Configuration file
creating 8-21
editing 8-23
loading 8-22
saving 8-21
Configuration File - Generate Default 8-20
Configuration Tabs 10-39–10-72
Configured floor markers more than maximum allowed 9-172
Connected 5-26
Connection Status 5-26
Connections 2-35–2-41
Direct 2-35
Construction Car Panel Inspection mode 9-4
Construction Car Panel Inspection Operation 6-22, 6-23
Construction Cartop Inspection mode 9-4
Construction Cartop Inspection Operation message 6-23
Construction Hoistway Access Inspection mode 9-4
Construction Hoistway Access Inspection Operation 6-23
Construction Inspection mode 9-5
Construction Inspection Operation message 6-23
Construction Machine Room Inspection mode 9-5
Construction Machine Room Inspection Operation 6-23
Construction Mode 2-1–2-85, 3-1–3-25
exiting 3-25
Faults 2-3
Overview 2-2
Required connections 2-3
Contactor drop delay 9-27
Contract Overspeed Test 4-54
Contract overspeed, Safety parameter 9-176
Contract speed, Safety parameter 9-176
Controller Main Computer Startup message 6-23
Controller Specifications 11-2
Controller Stop switch, iBox control 7-12
Controller View 9-1
Controller view 9-2
Correction and Stop, verifying 4-3
Correction profile 4-19, 9-154
Counterweight balancing 9-167
Counterweight balancing, preparing for final adjust 3-29
Counterweight derailment detector 3-21
Counterweight Derailment output 9-138
counterweight learn operation 9-167
Counterweight Learn procedure 3-28
Counterweight position parameter 9-167
Coupling rotational ratio 2-45
Coupling rotation ratio, adjusting car speed (System 12) 2-62
CP INSP. DISABLED message 6-19
Creating a Configuration file 8-21
creating a direct connection 2-39
Creating a new LAN connection 8-12
Cross Registration 10-63
Cross registration serial inputs 10-63
Cross registration serial outputs 10-63
Cross-cancellation 10-43
Crosshead Deflection Load Weigher 4-36
Cross-registration 10-42
CT INSP. DISABLED message 6-21
CTEX NO CWI CFG ERROR message 6-21
To Next Page
Loading...