Firmware (continued)
creating 7-27
library 7-25
updating 7-24
using Fibre Channel
interface 7-28
using ITDT Tool 7-27
using SCSI interface 7-28
FMR tape
create D-30
unmake D-34
update firmware D-29
foot pads
remove 8-121
replace 8-121
front panel
access door 2-4
control module 2-3
expansion module 2-3
I/O Station 2-3
Operator Panel 2-4
power button 2-4
FRUs 8-1
G
gear rack alignment 8-22
glossary H-1
H
hazards, possible 5-2, 7-3
height of tape library 2-31
host
sharing library 2-29
hp-ux system error information E-8
I
I/O Station 2-3, 8-36, 8-37, 8-39, 8-40,
8-42
close door 6-69
lock assembly
remove 8-36
lock diagnostic 6-64
manually unlock door 7-42, 7-43,
8-34
remove 8-35
remove/replace 8-33
IBM Ultrium Tape Drive 2-11
Insert Cartridge D-35
install 8-121
installation
rack
safety 5-4
interfaces, supported 2-11
interior components 2-7
picker assembly 2-8
robotic system 2-8
Storage column 2-8
inventory library 6-68
K
Kerberos 2-30
key path diagnostics 7-13
periodic 7-15
using 7-14
Keyboards 4-4
L
Labels
bar code D-9
guidelines for using D-9
ordering D-17
laser
compliance 5-3
safety 5-3
LDAP 2-30
LEDs
drive 7-20
fibre port link 7-20
interpreting 7-16
library control blade 7-18, 7-19
picker 7-22
power supply 7-21
library
taking offline 7-38
taking online 7-38
library access, monitored 5-3
library and drive code update 2-23
library configuration form 7-19
Library Control Blade 2-5
remove/replace 8-45
library log file 2-17
library state required 8-2
Library Verify Test 6-64, 7-6
bar code scanner diagnostic 6-63
general drive diagnostic 6-62
motion failure diagnostic 6-62
licenses 2-12
advanced reporting 2-12
capacity expansion 2-19
encryption 2-22
path failover 2-22
LME Key Path 7-13
Load/Unload Test D-39
location coordinates 2-23
columns 2-25
drives 2-25
modules 2-24
power supplies 2-25
slots 2-25
lock assembly 8-37
logical libraries
sharing 2-29
logs 7-10
capturing 7-10
e-mailing 7-12
media usage 2-16
low voltage differential (LVD) SCSI
interface 2-11
low-power mode 2-11
LVD SCSI interface 2-11
M
M2 Robot Assembly
remove/replace 8-67
Maintenance
create FMR tape D-30
update firmware with FMR
tape D-29
Maintenance Function
selecting function D-26
unmaking an FMR tape D-34
Maintenance Mode
entering D-27
exiting D-28
Maintenance plan 2-32
Maintenance start 2-33
McDATA switch D-54
Media D-5
inserting D-4
removing D-5
unassigned D-13
Unlabeled D-11
unsupported format diagnostic 6-66
Write Protect or WORM
Diagnostic 6-66
media integrity 2-14
media integrity reporting 2-14
media security notifications 2-16
media usage logs 2-16
Menus
Operator Panel 4-5
service 7-4
Message codes D-41
messages, drive error
Drive Error Log D-51
Error Messages, Receiving D-49
Host Sense Data D-50
Messages, Receiving D-49
mixed drive types, protection against
non-support 2-29
module coordinates 2-24
monitored library access 5-3
motion obstructed 6-71
Multi-Path Architecture 2-29
multiple control paths
for control path failover 2-29
O
offline library 7-38
online library 7-38
operating systems supported 2-33
operator interventions 7-2
operator panel
login 4-1
Operator Panel 2-4, 4-1, 8-28
capacity view 4-4
common elements 4-3
header elements 4-3
keyboards 4-4
menus 4-5
subsystem status 4-3
system summary 4-3
Index
X-3
To Next Page
Loading...
Need help?
General
