Figures
2-1. Front panel of a 14U library ......2-2
2-2. Rear panel of a 14U library ......2-5
2-3. The library control blade .......2-6
2-4. Storage columns ..........2-8
2-5. Y-Axis/Picker Assembly .......2-9
2-6. M2 Robot Assembly .........2-9
2-7. M2 Label on the M2 Robot Assembly 2-10
2-8. Ultra160 SCSI Tape Drives in the library
control module ..........2-11
2-9. Library Location Coordinates .....2-24
2-10. Drive location coordinates ......2-25
2-11. Power supply location coordinates 2-26
2-12. Ultrium Cartridge .........2-27
3-1. Front view of a 14U library with the I/O
Station door open .........3-2
3-2. Rear view of a 5U library .......3-2
3-3. Rear view of a 14U library ......3-3
3-4. I/O Station Lock Assembly installed in the
library .............3-3
3-5. I/O Station Lock Assembly (top view) 3-4
3-6. I/O Station with Slide Assembly ....3-4
3-7. Access Door open showing back of
Operator Panel ..........3-5
3-8. Gear racks inside the library ......3-6
3-9. Original Y-axis/Picker Assembly ....3-7
3-10. M2 Robot Assembly .........3-7
3-11. Home Sensor Flag .........3-8
3-12. Cable spool assembly ........3-9
3-13. Library Control Blade (external library
view) .............3-10
3-14. Library Control Blade and Compact Flash
Card .............3-11
3-15. Power Supply ..........3-12
3-16. LTO 3 drive sleds .........3-13
4-1. Operator Panel Login screen for firmware
versions prior to 585G ........4-1
4-2. Operator Panel Login screen for firmware
versions 585G and later .......4-2
4-3. Operator Panel common header elements
and subsystem status buttons .....4-3
4-4. Home Screen Capacity View ......4-4
4-5. Setup menu screen .........4-5
4-6. Operations menu screen .......4-6
4-7. Tools menu screen .........4-7
5-1. SnapHat battery holder ........5-9
6-1. Calibration Sensor .........6-85
7-1. Power button LEDs ........7-17
7-2. Library Control Blade LEDs ......7-18
7-3. Tape drive LEDs .........7-20
7-4. Power supply LEDs ........7-21
7-5. Location of Original Picker Assembly LED 7-23
7-6. Location of M2 Picker Assembly LED 7-24
7-7. Cabling of a 5U Library with SCSI Drives 7-29
7-8. Cabling of a 14U Library with Fibre Drives 7-30
7-9. Cabling of a Multi-Module Library with
SCSI and Fibre Drives........7-31
7-10. Operator panel connectors ......
7-32
7-11. I/O Station lock assembly connector (top
cover removed) ..........7-33
7-12. Backplane Connect Board connectors
(front, top cover removed) ......7-34
7-13. Backplane Connect Board connectors (back,
drive sleds removed) ........7-34
7-14. Drive Sled Interface Board connectors (side
cover removed) ..........7-35
7-15. Spooler cable connector and original
Y-motor assembly connectors .....7-36
7-16. Original picker assembly connector 7-37
7-17. Spooler cable connector and M2 Robot
controller board connectors ......7-37
7-18. Picker rotated for drive gears access 7-41
7-19. Access the M2 Picker Thumbwheel 7-41
7-20. Access holes for manually unlocking I/O
Station doors ...........7-42
7-21. RID tag placement .........7-43
7-22. Agency Label placement .......7-44
7-23. The Floor Plate ..........7-45
8-1. Picker locking mechanism .......8-6
8-2. Gear racks and gear rack locking
mechanism ............8-7
8-3. Front and back gear racks .......8-8
8-4. Gear racks in the up and down positions 8-8
8-5. Placing gear rack in Up position ....8-9
8-6. Releasing the Y-rail.........8-10
8-7. Control module rear thumb screws 8-11
8-8. Alignment pin and front thumb screw 8-11
8-9. Gear racks (down and up) ......8-12
8-10. Alignment pin and front thumb screw
receptacles ...........8-13
8-11. Control module rear thumb screws 8-14
8-12. Gear racks and gear rack locking
mechanism ...........8-15
8-13. Front and back gear racks ......8-16
8-14. Gear racks in the up and down positions 8-16
8-15. Placing gear rack in the Down position 8-17
8-16. Releasing the Y-rail.........8-18
8-17. Removing the rack ears (Control Module
shown).............8-21
8-18. Gear rack ............8-22
8-19. Front and back gear racks ......8-23
8-20. Gear racks in the up and down positions 8-24
8-21. Placing gear rack in the Down position 8-24
8-22. Releasing the Y-rail.........8-25
8-23. Picker assembly locking mechanism 8-26
8-24. Control module Access Door screw
locations ............8-27
8-25. Expansion module Access Door screw
locations ............8-28
8-26. Operator Panel assembly .......8-29
8-27. Connector on the back of the I/O Station
locking mechanism.........8-30
© Copyright IBM Corp. 2005, 2010 xiii
||
|
||
|
||
||
||
||
||
||
||
||
||
||
||
||
||
To Next Page
Loading...
Need help?
General
