Rohde & Schwarz R&S ZNA Series - Page 1109

Command reference
R&S
®
ZNA
1109User Manual 1178.6462.02 ─ 29
'BP2/A1' | ... 'BP02/A01' | ... | 'BP2/A1SAM' | 'B2/
AP1RMS' | 'B2/AP1PEAK' | 'B2/AP1AVG' | ...
Ratio of primed or/unprimed wave quantities with port numbers like for nor-
mal mode S-parameters. The strings SAM, RMS, PEAK, AVG appended to
the wave quantities denote a normal (sample), RMS, peak, or average
detector.
'BP2D1/A1D1' | ... 'BP02D01/A01D01' | ... 'BP2D1/
A1D1SAM' | 'B2D1/AP1D1RMS' | 'BP2D1/
AP1D1PEAK' | 'BP2D1/AP1D1AVG'...
Ratio of primed/unprimed wave quantities with port numbers and source port
numbers (D<no> for drive port). The strings SAM, RMS, PEAK, AVG appen-
ded to the wave quantities denote a normal (sample), RMS, peak, or aver-
age detector.
'BP2G1/A1G1' | ... 'BP02G1/A01G1' | ... 'B2G1/
AP1G1SAM' | 'B2G1/AP1G1RMS' | 'BP2G1/
AP1G1PEAK' | 'BP2G1/AP1G1AVG' | ...
Ratio of primed/unprimed wave quantities with port numbers and external
generator providing the stimulus signal (G<no> for generator no.). The
strings SAM, RMS, PEAK, AVG appended to the wave quantities denote a
normal (sample), RMS, peak, or average detector.
'IMB21' | 'IMB12' | 'IMB31' | ... Imbalance parameter Imb<receive_port><drive_port> for logical port num-
bers <receive_port> and <drive_port>. The logical ports must be different
and at least one of them must be balanced.
'CMRR11' | 'CMRR21' | 'CMRR12' | 'CMRR22' | ... Common mode rejection ratio CMRR<receive_port><drive_port> parameter
for logical port numbers <receive_port> and <drive_port>, at least one of
them balanced.
'IMB1-23' | 'IMB23-1' | 'IMB1-24' | ... Differential Imbalance parameters between a balanced and two single-ended
logical ports
'KFAC21' | 'KFAC12' | ... Stability factor K (for unbalanced ports only)
'MUF121' | 'MUF112' | ... Stability factor 1 (for unbalanced ports only)
'MUF221' | 'MUF212' | ... Stability factor 2 (for unbalanced ports only)
'Pmtr1G1' | 'Pmtr2G1' | 'Pmtr3D1' | ... Power sensor measurement using a power meter 'Pmtr<no>' and either an
external generator 'G<no>' or an analyzer source port 'D<no>'
'PAE21' | PAE12' | ... Power added efficiency (referring to logical ports)
'IM3UI' | 'IM3UO' | 'IM3LI' | 'IM3LO' | 'IM3MI' |
'IM3MO' | 'IM5UI' ... 'IM9MO'
Intermodulation product IM<order><side><at DUT> where <order> = 3 | 5 | 7
| 9, <side> = U | L | M (for upper or lower or major), <at DUT> = I | O (for
input or output)
'IM3UIR' | 'IM3UOR' | 'IM3LIR' | 'IM3LOR' | 'IM3MIR'
| 'IM3MOR' | 'IM5UIR' ... 'IM9MOR'
Intermodulation product (as explained above) displayed in dB units relative
to the measured lower tone level at DUT input or output ("intermodulation
suppression")
'IP3UI' | 'IP3UO' | 'IP3LI' | 'IP3LO' | 'IP3MI' | 'IP3MO'
| 'IP5UI' ... 'IP9MO'
Intercept point IP<order><side><at DUT> where <order> = 3 | 5 | 7 | 9,
<side> = U | L | M (for upper or lower or major), <at DUT> = I | O (for input or
output)
UTI | UTO | LTI | LTO Upper or lower tone at DUT input or output
NLO Noise level at DUT output
Requires option R&S ZNA-K30.
'NF12' | 'NF13' | ... | 'NF21' | 'NF23' | ... Noise figure parameters NF<out><in>, where <out> and <in> denote the
output and input port numbers of the DUT, and <out>≠<in>.
Requires option R&S ZNA-K30.
'ND1' | 'ND2' | ... Noise (power spectral) density, measured at receive port 1, 2, ...
Requires option R&S ZNA-K30.
'b1/a2' | 'b1/a3' | ... | 'b2/a1' | 'b2/a3' | ... Gain of the DUT, as measured in noise figure channels
Requires option R&S ZNA-K30.
SCPI command reference