Rohde & Schwarz R&S ZNA Series - 7.3.14.22 [SENSe:]SWEep...

Command reference
R&S
®
ZNA
1499User Manual 1178.6462.02 ─ 29
Suffix:
<Ch>
.
Channel number
Parameters:
<Boolean> 1 (ON)
Zero padding used (higher level accuracy)
0 (OFF)
Zero padding used (higher level accuracy, in particular for multi-
channel measurements)
*RST: 1 (ON)
Options: R&S ZNA-K1
Manual operation: See "Increased Level Accuracy" on page 400
7.3.14.22
[SENSe:]SWEep...
The [SENSe:]SWEep... commands provide general settings to control the sweep.
Most of the settings have an impact on the sweep time.
[SENSe<Ch>:]SWEep:AXIS:FREQuency....................................................................... 1500
[SENSe<Ch>:]SWEep:AXIS:POWer.............................................................................. 1501
[SENSe<Ch>:]SWEep:COUNt.......................................................................................1501
[SENSe:]SWEep:COUNt:ALL........................................................................................1502
[SENSe<Ch>:]SWEep:CTIMing:CHANnel...................................................................... 1502
[SENSe<Ch>:]SWEep:CTIMing:CHANnel:MODE............................................................1502
[SENSe<Ch>:]SWEep:CTIMing:COMPression................................................................1503
[SENSe<Ch>:]SWEep:CTIMing:COMPression:MODE..................................................... 1503
[SENSe<Ch>:]SWEep:CTIMing:MODE.......................................................................... 1504
[SENSe<Ch>:]SWEep:CTIMing:OCHannel.....................................................................1504
[SENSe<Ch>:]SWEep:CTIMing:OCHannel:MODE.......................................................... 1504
[SENSe<Ch>:]SWEep:CTIMing:PORT:MAX................................................................... 1505
[SENSe<Ch>:]SWEep:CTIMing:PORT:MAX:MODE.........................................................1505
[SENSe<Ch>:]SWEep:CTIMing:PORT:MIN.....................................................................1505
[SENSe<Ch>:]SWEep:CTIMing:PORT:MIN:MODE..........................................................1506
[SENSe<Ch>:]SWEep:CTIMing:SEGMent......................................................................1506
[SENSe<Ch>:]SWEep:CTIMing:SEGMent:MODE........................................................... 1507
[SENSe<Ch>:]SWEep:CTIMing:STIMe.......................................................................... 1507
[SENSe<Ch>:]SWEep:CTIMing:STIMe:MODE................................................................1507
[SENSe<Ch>:]SWEep:CTIMing:STIMe:MAX...................................................................1508
[SENSe<Ch>:]SWEep:CTIMing:STIMe:MIN....................................................................1508
[SENSe<Ch>:]SWEep:CTIMing:VISualize...................................................................... 1509
[SENSe<Ch>:]SWEep:DETector:TIME........................................................................... 1509
[SENSe<Ch>:]SWEep:DWELl....................................................................................... 1509
[SENSe<Ch>:]SWEep:DWELl:IPOint............................................................................. 1510
[SENSe<Ch>:]SWEep:FPOWer.....................................................................................1510
[SENSe<Ch>:]SWEep:GENeration................................................................................ 1511
[SENSe<Ch>:]SWEep:POINts.......................................................................................1511
[SENSe<Ch>:]SWEep:REVerse.................................................................................... 1512
[SENSe<Chn>:]SWEep:SRCPort...................................................................................1512
[SENSe<Ch>:]SWEep:STEP.........................................................................................1513
SCPI command reference