Rohde & Schwarz R&S ZNA Series - CALCulate:FMODel:ISD...

Command reference
R&S
®
ZNA
1038User Manual 1178.6462.02 ─ 29
Manual operation: See "Run <Fixture Modeling Tool>" on page 734
CALCulate:FMODel:EZD<Pt>:RUN[:STATe] <Boolean>
Tells the analyzer to assign deembedding files to certain ports, after the EZD tool has
run.
Suffix:
<Pt>
.
Physical port number for single-ended deembedding, logical port
number for balanced deembedding.
Parameters:
<Boolean> ON (1)
Assign a deembedding file to port <Pt>
OFF (0)
Otherwise
Options: R&S ZNA-K210
Manual operation: See "Apply" on page 735
CALCulate:FMODel:ISD...
Commands for AtaiTec's In Situ De-Embedding (ISD) tool, see http://ataitec.com/prod-
ucts/isd/
CALCulate:FMODel:ISD:ATTenuation:BEHavior..............................................................1039
CALCulate:FMODel:ISD:COUPon:MEASure...................................................................1039
CALCulate:FMODel:ISD:COUPon:MEASure:FILename................................................... 1039
CALCulate:FMODel:ISD:COUPon:MEASure:FILename:CLEar......................................... 1040
CALCulate:FMODel:ISD:COUPon:MEASure:OPEN.........................................................1040
CALCulate:FMODel:ISD:COUPon:MEASure:OPEN:FILename......................................... 1040
CALCulate:FMODel:ISD:COUPon:MEASure:SHORt........................................................1040
CALCulate:FMODel:ISD:COUPon:MEASure:SHORt:FILename........................................ 1040
CALCulate:FMODel:ISD<Ph_pt>:COUPon[:STATe]......................................................... 1041
CALCulate:FMODel:ISD:COUPon:TYPE........................................................................ 1041
CALCulate:FMODel:ISD:DCEXtrapolat...........................................................................1041
CALCulate:FMODel:ISD:DUT:MEASure......................................................................... 1042
CALCulate:FMODel:ISD:DUT:MEASure:FILename..........................................................1042
CALCulate:FMODel:ISD:DUT:MEASure:FILename:CLEar................................................1042
CALCulate:FMODel:ISD<Ph_pt>:DUT[:STATe]................................................................1042
CALCulate:FMODel:ISD:DUT:TYPE...............................................................................1042
CALCulate:FMODel:ISD:FTIMe:DUT..............................................................................1043
CALCulate:FMODel:ISD:FTIMe:OVERride......................................................................1043
CALCulate:FMODel:ISD:IMPedance.............................................................................. 1043
CALCulate:FMODel:ISD:OPERation.............................................................................. 1043
CALCulate:FMODel:ISD:PASSivity................................................................................ 1044
CALCulate:FMODel:ISD:PORT:ORDer...........................................................................1044
CALCulate:FMODel:ISD:PORT:SKIP..............................................................................1044
CALCulate:FMODel:ISD:PORT:SKIP:LEFT.....................................................................1045
CALCulate:FMODel:ISD:PORT:SKIP:NONE................................................................... 1045
CALCulate:FMODel:ISD:PORT:SKIP:RIGHt....................................................................1045
SCPI command reference