Rohde & Schwarz R&S ZNA Series - 7.3.1.12 CALCulate:RIPPle...

Command reference
R&S
®
ZNA
1111User Manual 1178.6462.02 ─ 29
CALCulate<Ch>:PARameter:SELect <TraceName>
Selects an existing trace as the active trace of the channel. All trace commands with-
out explicit reference to the trace name act on the active trace (e.g.
CALCulate<Chn>:FORMat). CALCulate<Ch>:PARameter:SELect is also neces-
sary if the active trace of a channel has been deleted.
Suffix:
<Ch>
.
Channel number.
Parameters:
<TraceName> Trace name, e.g. 'Trc4'. See "Rules for trace names" in "Table
Area" on page 435.
Example:
CALC4:PAR:SDEF 'Ch4Tr1', 'S11'
Create channel 4 and a trace named Ch4Tr1 to measure the
input reflection coefficient S
11
. The trace is the active trace in
channel 4.
CALC4:PAR:SDEF 'Ch4Tr2', 'S22'
Create another trace named Ch4Tr2 to measure the output
reflection coefficient S
22
. Again this new trace becomes the
active trace in channel 4.
CALC4:PAR:SEL 'Ch4Tr1'
Select the first trace Ch4Tr1 as the active trace.
CALC4:FORM MLIN
Calculate the magnitude of S
11
and display it in a linearly scaled
Cartesian diagram.
7.3.1.12 CALCulate:RIPPle...
The CALCulate:RIPPle... commands define the ripple limits and control the ripple
limit check.
CALCulate<Chn>:RIPPle:CLEar.................................................................................... 1112
CALCulate<Chn>:RIPPle:CONTrol:DOMain.................................................................... 1112
CALCulate<Chn>:RIPPle:DATA..................................................................................... 1112
CALCulate<Chn>:RIPPle:DELete:ALL............................................................................ 1113
CALCulate:RIPPle:DISPlay:RESult:ALL[:STATe].............................................................. 1114
CALCulate<Chn>:RIPPle:DISPlay[:STATe]......................................................................1114
CALCulate<Chn>:RIPPle:FAIL?..................................................................................... 1114
CALCulate:RIPPle:FAIL:ALL?........................................................................................ 1115
CALCulate<Chn>:RIPPle:RDOMain:FORMat.................................................................. 1115
CALCulate<Chn>:RIPPle:SEGMent:COUNt?.................................................................. 1116
CALCulate<Chn>:RIPPle:SEGMent<Seg>:LIMit.............................................................. 1116
CALCulate<Chn>:RIPPle:SEGMent<Seg>:RESult?......................................................... 1117
CALCulate<Chn>:RIPPle:SEGMent<Seg>[:STATe].......................................................... 1117
CALCulate<Chn>:RIPPle:SEGMent<Seg>:STIMulus:STARt............................................. 1118
CALCulate<Chn>:RIPPle:SEGMent<Seg>:STIMulus:STOP..............................................1118
CALCulate<Chn>:RIPPle:SOUNd[:STATe]...................................................................... 1118
CALCulate<Chn>:RIPPle:STATe.................................................................................... 1119
CALCulate<Chn>:RIPPle:STATe:AREA...........................................................................1119
SCPI command reference