Rohde & Schwarz R&S ZNA Series - 7.3.15.12 SOURce:POWer... (other)

Command reference
R&S
®
ZNA
1580User Manual 1178.6462.02 ─ 29
Parameters:
<CPRReceiver> 'A1' | 'B1' | 'A2' | ... (string parameter)
Manual operation: See "Meas Port/Meas Receiver (table area)" on page 532
SOURce<Ch>:POWer<Pt>:CPRemeas[:STATe] <Boolean>
Enables cal premeas for port <Pt> in channel <Ch>.
Only takes effect, if cal premeas is enabled for channel <Ch> (SOURce<Ch>:POWer:
CPRemeas:CSTate ON).
Suffix:
<Ch>
.
Channel number
<Pt> Port number
Parameters:
<Boolean> ON (1) | OFF (0)
*RST: OFF (0)
Manual operation: See "Cal Premeas On (table area)" on page 532
7.3.15.12 SOURce:POWer... (other)
The SOURce:POWer... commands define the power of the internal signal source.
SOURce<Ch>:POWer<PhyPt>:ATTenuation...................................................................1581
SOURce<Ch>:POWer<PhyPt>:CONVerter:OFFSet.........................................................1581
SOURce<Ch>:POWer<PhyPt>:CORRection:GENerator<Gen>:LEVel:OFFSet...................1582
SOURce<Ch>:POWer<PhyPt>:CORRection:LEVel:OFFSet............................................. 1583
SOURce<Ch>:POWer<Pt>:EATTenuation...................................................................... 1583
SOURce<Ch>:POWer<Pt>:EATTenuation:MODE............................................................1584
SOURce<Ch>:POWer<PhyPt>:GENerator<Gen>:OFFSet............................................... 1584
SOURce<Ch>:POWer<PhyPt>:GENerator<Gen>:PERManent[:STATe]............................. 1585
SOURce:POWer:GENerator:SDELay.............................................................................1586
SOURce<Ch>:POWer<PhyPt>:GENerator<Gen>:STATe................................................. 1586
SOURce<Ch>:POWer<PhyPt>:GENerator<Gen>:LLIMit[:STATe]......................................1586
SOURce<Ch>:POWer<PhyPt>:GENerator<Gen>:LLIMit:VALue....................................... 1587
SOURce<Ch>:POWer<PhyPt>[:LEVel][:IMMediate][:AMPLitude]...................................... 1587
SOURce<Ch>:POWer<PhyPt>[:LEVel][:IMMediate]:LLIMit[:STATe]................................... 1588
SOURce<Ch>:POWer<PhyPt>[:LEVel][:IMMediate]:LLIMit:VALue.....................................1588
SOURce<Ch>:POWer<PhyPt>[:LEVel][:IMMediate]:OFFSet............................................ 1589
SOURce<Ch>:POWer<PhyPt>[:LEVel][:IMMediate]:SLOPe............................................. 1590
SOURce<Ch>:POWer<PhyPt>:PERManent[:STATe]....................................................... 1590
SOURce:POWer:REDuce:SDELay................................................................................ 1591
SOURce<Ch>:POWer<PhyPt>:REDuce[:STATe].............................................................1591
SOURce<Ch>:POWer<PhyPt>:STATe............................................................................1592
SOURce<Ch>:POWer<PhyPt>:STARt........................................................................... 1592
SOURce<Ch>:POWer<PhyPt>:STOP............................................................................ 1592
SOURce:POWer:SWEepend:MODE.............................................................................. 1593
SOURce:POWer:SWEepend:SDELay............................................................................1593
SCPI command reference