Lucent Technologies CBX 3500 - Page 25

Contents
ATM Services Configuration Guide for CBX 3500, CBX 500, GX 550, and B-STDX 9000 1/19/05xxv
Beta Draft Confidential
Figure 8-19. Add Logical Port: General Tab..................................................... 8-36
Figure 8-20. Add Logical Port: Administrative Tab......................................... 8-37
Figure 8-21. Add Logical Port: QoS Tab.......................................................... 8-40
Figure 8-22. Add Logical Port: Traffic Descriptors Tab................................... 8-42
Figure 8-23. Managing Trunks.......................................................................... 8-43
Figure 8-24. Add Trunk Dialog Box................................................................. 8-44
Figure 8-25. Select Trunk Endpoints Dialog Box............................................. 8-44
Figure 9-1. Layer 2 Tunnel Over MPLS Core Network ................................... 9-4
Figure 9-2. PWE3 Over MPLS Core Network.................................................. 9-5
Figure 9-3. Add Affinity Dialog Box................................................................ 9-7
Figure 9-4. Add Hoplist Dialog Box................................................................. 9-8
Figure 9-5. Add Intserv Dialog Box................................................................ 9-11
Figure 9-6. Add Diffserv Dialog Box.............................................................. 9-13
Figure 9-7. Modify Switch: MPLS Tab .......................................................... 9-17
Figure 9-8. Managing POS PPorts and LPorts................................................ 9-19
Figure 9-9. Add Logical Port Dialog Box: Point-to-Point.............................. 9-20
Figure 9-10. Add Logical Port: Administrative Tab......................................... 9-22
Figure 9-11. Add Logical Port: QoS Tab.......................................................... 9-24
Figure 9-12. Add Logical Port: Trap Control Tab ............................................ 9-26
Figure 9-13. Add Logical Port: MPLS Tab....................................................... 9-28
Figure 9-14. Add Logical Port: Congestion Control Tab.................................. 9-30
Figure 9-15. Add Logical Port: Point to Point Tab........................................... 9-31
Figure 9-16. Add IP Lport Dialog Box ............................................................. 9-32
Figure 9-17. RsvpTE Instance Node in Switch Tab.......................................... 9-34
Figure 9-18. Modify RsvpTE Dialog Box......................................................... 9-35
Figure 9-19. Add IP Interface Address Dialog Box.......................................... 9-38
Figure 9-20. Add OSPF IP Interface Dialog Box.............................................. 9-40
Figure 9-21. Add Tunnel: General Tab............................................................. 9-44
Figure 9-22. Add Tunnel: General Tab............................................................. 9-45
Figure 9-23. Add Tunnel: RSVP-TE Tab.......................................................... 9-48
Figure 9-24. Add Tunnel: Static Tab................................................................. 9-49
Figure 9-25. Add Layer2 Tunnel Dialog Box................................................... 9-52
Figure 9-26. Add Layer2 Tunnel: ATM Tab..................................................... 9-54
Figure 9-27. Add Layer2 Tunnel: VNN Tab..................................................... 9-56
Figure 9-28. Add Layer2 Tunnel: PNNI Tab.................................................... 9-58
Figure 9-29. Add LDP Entity Dialog Box......................................................... 9-62
Figure 9-30. Add PVC: Pwe3 Tab .................................................................... 9-65
Figure 10-1. Right-Clicking on the PVCs Node ............................................. 10-11
Figure 10-2. Right-Clicking on a Circuit ........................................................ 10-12
Figure 10-3. Add PVC Dialog Box................................................................. 10-13
Figure 10-4. Select Endpoints Dialog Box...................................................... 10-14
Figure 10-5. Add PVC: Traffic Type Tab....................................................... 10-22
Figure 10-6. Add PVC: User Preference Tab.................................................. 10-26
Figure 10-7. Add PVC: Traffic Mgmt. Tab .................................................... 10-31
Figure 10-8. Add Redirect PVC Dialog Box................................................... 10-35
Figure 10-9. Select Endpoints Dialog Box (Redirect PVCs) .......................... 10-36
Figure 10-10. Add Redirect PVC: Administrative Tab..................................... 10-38
Figure 10-11. Add PVC Dialog Box (FR-ATM) .............................................. 10-48