Rohde & Schwarz R&S ZNA Series - Page 1478

Command reference
R&S
®
ZNA
1478User Manual 1178.6462.02 ─ 29
[SENSe<Ch>:]SEGMent<Seg>:ADD..............................................................................1478
[SENSe<Ch>:]SEGMent<Seg>:BWIDth[:RESolution]...................................................... 1479
[SENSe<Ch>:]SEGMent<Seg>:BWIDth[:RESolution]:CONTrol.........................................1479
[SENSe<Ch>:]SEGMent<Seg>:BWIDth[:RESolution]:SELect........................................... 1480
[SENSe<Ch>:]SEGMent<Seg>:BWIDth[:RESolution]:SELect:CONTrol..............................1480
[SENSe<Ch>:]SEGMent:COUNt?..................................................................................1481
[SENSe<Ch>:]SEGMent<Seg>:DEFine..........................................................................1482
[SENSe<Ch>:]SEGMent<Seg>:DEFine:SELect.............................................................. 1483
[SENSe<Ch>:]SEGMent<Seg>:DELete:ALL................................................................... 1484
[SENSe<Ch>:]SEGMent<Seg>:DELete[:DUMMy]........................................................... 1484
[SENSe<Ch>:]SEGMent<Seg>:FREQuency:CENTer?.....................................................1484
[SENSe<Ch>:]SEGMent<Seg>:FREQuency:SPAN?........................................................1484
[SENSe<Ch>:]SEGMent<Seg>:FREQuency:STARt.........................................................1485
[SENSe<Ch>:]SEGMent<Seg>:FREQuency:STOP......................................................... 1485
[SENSe<Ch>:]SEGMent<Seg>:INSert........................................................................... 1485
[SENSe<Ch>:]SEGMent<Seg>:INSert:SELect................................................................ 1487
[SENSe<Ch>:]SEGMent<Seg>:NFIGure:VIRejection[:STATe]...........................................1488
[SENSe<Ch>:]SEGMent:NFIGure:VIRejection:STATe:CONTrol........................................ 1488
[SENSe<Ch>:]SEGMent<Seg>:PORT<PortId>:POWer[:LEVel].........................................1489
[SENSe<Ch>:]SEGMent<Seg>:PORT<PortId>[:STATe]................................................... 1489
[SENSe<Ch>:]SEGMent<Seg>:POWer:GAINcontrol....................................................... 1490
[SENSe<Ch>:]SEGMent<Seg>:POWer:GAINcontrol:ALL.................................................1491
[SENSe<Ch>:]SEGMent<Seg>:POWer:GAINcontrol:CONTrol..........................................1491
[SENSe<Ch>:]SEGMent<Seg>:POWer[:LEVel]...............................................................1492
[SENSe<Ch>:]SEGMent:POWer[:LEVel]:CONTrol...........................................................1492
[SENSe<Ch>:]SEGMent<Seg>[:STATe]......................................................................... 1493
[SENSe<Ch>:]SEGMent<Seg>:SWEep:DWELl...............................................................1494
[SENSe<Ch>:]SEGMent<Seg>:SWEep:DWELl:CONTrol................................................. 1494
[SENSe<Ch>:]SEGMent<Seg>:SWEep:POINts.............................................................. 1495
[SENSe<Ch>:]SEGMent<Seg>:SWEep:TIME.................................................................1495
[SENSe<Ch>:]SEGMent<Seg>:SWEep:TIME:CONTrol................................................... 1496
[SENSe<Ch>:]SEGMent<Seg>:SWEep:TIME:SUM?....................................................... 1497
[SENSe<Ch>:]SEGMent<Seg>:ADD
Inserts a new sweep segment using default channel settings ("Insert New Segment").
The added segment covers the frequency interval between the maximum frequency of
the existing sweep segments and the stop frequency of the entire sweep range.
Tip: Use [SENSe<Ch>:]SEGMent<Seg>:INSert to create a segment with specific
channel settings.
Suffix:
<Ch>
.
Channel number
<Seg> Sweep segment number. Segment numbers must be sequential.
If n segments exist already, the added segment must have the
segment number n+1.
SCPI command reference