Rohde & Schwarz R&S ZNA Series - Page 1794

Annexes
R&S
®
ZNA
1794User Manual 1178.6462.02 ─ 29
ENA Emulation Command R&S ZNA Default Parser Command
SENSe{1...4}:SWEep:MOD CONTinuous |
HOLD | SINGle
SENSe{1...4}:SWEep:MODE CONTinuous |
HOLD | SINGle
SENSe{1...4}:SWEep:POINts <numeric>
[SENSe<Ch>:]SWEep:POINts
SENSe{1...4}:SWEep:TIME[:DATA]
<numeric>
[SENSe<Ch>:]SWEep:TIME
SENSe{1...4}:SWEep:TIME:AUTO {ON | OFF
| 1 | 0}
[SENSe<Ch>:]SWEep:TIME:AUTO
SENSe{1...4}:SWEep:TYPE {LINear |
SEGMent}
[SENSe<Ch>:]SWEep:TYPE
SERVice:CHANnel:COUNt?
n.a. (no limit)
SERVice:CHANnel:TRACe:COUNt?
n.a. (no limit)
SOURce{1...4}:POWer[:LEVel][:
IMMediate][:AMPLitude] <numeric>
SOURce<Ch>:POWer<PhyPt>[:LEVel][:
IMMediate][:AMPLitude]
SOURce<ch>:POWer<pt>:CORRection[:
STATe] {ON | OFF | 1 | 0}
SOURce<Ch>:POWer<PhyPt>:CORRection:
STATe
SOURce<ch>:POWer<pt>:CORRection:
COLLect:AVERage[:COUNt] <numeric>
SOURce:POWer:CORRection:COLLect:
AVERage[:COUNt]
SOURce:POWer<pt>:CORRection:COLLect:
AVERage:NTOLerance <numeric>
SOURce:POWer:CORRection:COLLect:
AVERage:NTOLerance
SOURce<ch>:POWer<pt>:CORRection:
COLLect:SAVE [<RREC>]
n.a. (instrument automatically applies calibration
after it is complete)
SOURce{1..4}:POWer:PORT:COUPle {ON |
1}
STATus:OPERation:CONDition?
STATus:QUEStionable:CONDition?
STATus:OPERation:ENABle <numeric>
STATus:QUEStionable:ENABle
STATus:OPERation[:EVENt]?
STATus:QUEStionable[:EVENt]?
STATus:QUEStionable:NTRansition
<numeric>
STATus:QUEStionable:NTRansition
STATus:QUEStionable:PTRansition
<numeric>
STATus:QUEStionable:LIMit<Lev>:
PTRansition
STATus:QUEStionable:LIMit:CONDition?
STATus:QUEStionable:LIMit<Lev>:
CONDition?
STATus:QUEStionable:LIMit:ENABle
<numeric>
STATus:QUEStionable:LIMit<Lev>:ENABle
STATus:QUEStionable:LIMit[:EVENt]?
STATus:QUEStionable:LIMit<Lev>[:
EVENt]?
STATus:QUEStionable:LIMit:NTRansition
<numeric>
STATus:QUEStionable:LIMit<Lev>:
NTRansition
ENA emulation commands