Rohde & Schwarz R&S ZNA Series - Page 1845

Index
R&S
®
ZNA
1845User Manual 1178.6462.02 ─ 29
Reset values
Status reporting system ............................................ 966
Resolution Enh(ancement) ..............................................450
Response (to queries) ..................................................... 939
Restart Manager dialog ................................................... 568
Sweep Active Channel .............................................. 569
Sweep All Channels .................................................. 569
Restart Sweep .................................................................566
Restart Sweep on Std. Meas. ......................................... 578
Revision ............................................................................ 19
RF In Low / High ............................................................... 91
RF Off All Channels .........................................................526
RFFE Config dialog
Sweep Sequencer tab .............................................. 665
RFFE Config dialog (R&S ZN-B15/-Z15 Var. 03) ............ 656
GPIOs tab ................................................................. 658
RFFE tab .................................................................. 657
Sweep Sequencer tab .............................................. 658
RFFE interface
Configuration ............................................................ 659
R&S ZNA-B15 ........................................................... 305
RFFE Interface .................................................................. 42
RFFE interface configuration .......................................... 659
Apply changes (Set) ................................................. 662
Basic ......................................................................... 659
CLK ........................................................................... 660
R&S ZN-B15/-Z15 Var. 03 .........................................656
RFFE Command ....................................................... 660
SEND command ....................................................... 661
Seq. .......................................................................... 659
VHigh ........................................................................ 660
VIO ............................................................................660
VLow ......................................................................... 660
Voltage and current measurements .......................... 661
RFFE interface voltage and current measurements ....... 661
Apply configuration changes (Set) ............................ 662
Output Voltage .......................................................... 661
Range ....................................................................... 661
Results ...................................................................... 662
Shunt ........................................................................ 661
Start Meas ................................................................ 662
RFFE/GPIO interface
Sweep Sequencer .................................................... 665
Ripple limit .......................................................................168
files ........................................................................... 176
Ripple Test .............................................................. 487, 490
Clear Test ..................................................................489
Ranges ..................................................................... 490
Ripple Check ............................................................ 488
Ripple Fail Beep ....................................................... 489
Show Results All Traces ........................................... 489
Show Ripple Limits ................................................... 488
Rise Time ........................................................................ 826
S
S-parameter .................................................................... 149
multiport .................................................................... 150
S-parameter buttons ....................................................... 346
S-Parameter selector ...................................................... 345
S-Params tab .................................................................. 344
Converted admittances ............................................. 347
Converted impedances ............................................. 346
Safety instructions ....................................................... 15, 22
Warning messages ..................................................... 80
Same Color all Markers ...................................................850
Save (recall set) .............................................................. 774
Save Ripple Test ............................................................. 491
Saving data ....................................................................... 77
Scalar power calibration .......................................... 102, 218
Scale
Scale Coupling ..........................................................428
Scale Coupling tab .......................................................... 428
Scale softtool ...................................................................425
Scale Coupling tab ....................................................428
Scale Values tab ....................................................... 425
Zoom tab ...................................................................429
Scale Values tab ..............................................................425
Scale/Div ......................................................................... 427
Scaling diagrams ...............................................................66
Scan Instruments
external generators ........................................... 899, 923
external power meters .............................................. 893
External power meters .............................................. 911
SCPI command structure ................................................ 939
SCPI commands ............................................................. 939
SCPI status register ........................................................ 955
event status register ................................................. 959
IST flag ..................................................................... 959
parallel poll enable register ....................................... 959
service request enable register ................................. 958
status byte ................................................................ 958
STATus:OPERation register ......................................960
STATus:QUEStionable register ................................. 960
STATus:QUEStionable:INTegrity ...............................961
STATus:QUEStionable:LIMit ..................................... 960
Structure ................................................................... 953
Screen elements ............................................................. 124
Screen Keyboard ............................................................ 799
Screen saver ..................................................................... 35
SDC ...............................................................................1783
Search functions ............................................................. 132
Search Path for additional Cal Kits and Connector Types
........................................................................................ 860
Search Range dialog .......................................................506
Range Limit Lines On ............................................... 508
Search Range ........................................................... 507
Select Marker ............................................................ 507
Second internal LO generator ......................................... 303
Security procedures .......................................................... 22
Seg X-Axis ...................................................................... 551
Segmented IF Gain ......................................................... 689
Segmented sweep .......................................................... 548
Define Segments dialog ............................................ 553
Export segments ....................................................... 555
Import segments ....................................................... 555
Select Parameter dialog .................................................. 473
Select Ports dialog .......................................................... 474
Selectivity ........................................................................ 537
Selftest ............................................................................ 878
Selftest info ..................................................................... 878
SENSE
DC bias ....................................................................... 91
Sequential command execution ...................................... 949
Serial poll ........................................................................ 965
Service
Recalibration ........................................................... 1772
Service Function ..................................................... 885, 886
Password .................................................................. 886
Service Function dialog ................................................... 885
Service manual ................................................................. 22
Service request ............................................................... 964
Service request (SRQ) .................................................... 931
Service Request Enable ..........................................953, 958