Rohde & Schwarz R&S ZNA Series - Page 1211

Command reference
R&S
®
ZNA
1211User Manual 1178.6462.02 ─ 29
CONTrol<Ch>:RFFE<Bus>:COMMand:SEND................................................................ 1218
CONTrol<Ch>:RFFE<Bus>:COMMand:SEND?...............................................................1218
CONTrol<Ch>:RFFE<Bus>:SETTings:FREQuency......................................................... 1219
CONTrol<Ch>:RFFE<Bus>:SETTings[:STATe]................................................................ 1219
CONTrol<Ch>:RFFE<Bus>:SETTings:VOLTage:HIGH.....................................................1219
CONTrol<Ch>:RFFE<Bus>:SETTings:VOLTage:IO......................................................... 1219
CONTrol<Ch>:RFFE<Bus>:SETTings:VOLTage:LOW......................................................1219
CONTrol<Ch>:RFFE<Bus>:TEST:CLOCk.......................................................................1220
CONTrol<Ch>:RFFE<Bus>:TEST:DATA......................................................................... 1220
CONTrol<Ch>:RFFE<Bus>:TEST:VIO............................................................................1220
CONTrol:RFFE<Bus>:TEST:CLOCk:CURRent?.............................................................. 1220
CONTrol:RFFE<Bus>:TEST:DATA:CURRent?................................................................ 1220
CONTrol:RFFE<Bus>:TEST:VIO:CURRent?................................................................... 1220
CONTrol<Ch>:RFFE<Bus>:TEST:CLOCk:RANGe...........................................................1221
CONTrol<Ch>:RFFE<Bus>:TEST:DATA:RANGe............................................................. 1221
CONTrol<Ch>:RFFE<Bus>:TEST:VIO:RANGe................................................................1221
CONTrol<Ch>:RFFE<Bus>:TEST:CLOCk:SHUNt?..........................................................1221
CONTrol<Ch>:RFFE<Bus>:TEST:DATA:SHUNt?............................................................ 1221
CONTrol<Ch>:RFFE<Bus>:TEST:VIO:SHUNt?...............................................................1221
CONTrol:RFFE<Bus>:TEST:CLOCk:VOLTage?...............................................................1222
CONTrol:RFFE<Bus>:TEST:DATA:VOLTage?................................................................. 1222
CONTrol:RFFE<Bus>:TEST:VIO:VOLTage?....................................................................1222
CONTrol<Ch>:RFFE:TEST:OUTPut...............................................................................1222
CONTrol<Ch>:RFFE:TEST:SENSe:TRIGger...................................................................1223
CONTrol<Ch>:RFFE:TEST:TIME...................................................................................1223
CONTrol<Ch>:SEGMent<SegNr>:SEQuence<SeqNr>:DELay..........................................1223
CONTrol<Ch>:SEGMent<SegNr>:SEQuence<SeqNr>:GPIO<Port>:VOLTage................... 1224
CONTrol<Ch>:SEGMent<SegNr>:SEQuence<SeqNr>:RFFE<Bus>:COMMand:DATA........1224
CONTrol<Ch>:SEGMent<Nr>:SEQuence:CLEar:ALL...................................................... 1225
CONTrol<Ch>:SEGMent<Nr>:SEQuence:COUNt?..........................................................1225
CONTrol<Ch>:SEQuence:CLEar:ALL............................................................................ 1226
CONTrol<Ch>:SEQuence:COUNt?................................................................................1226
CONTrol<Ch>:SEQuence<Nr>:DELay........................................................................... 1226
CONTrol<Ch>:SEQuence<Nr>:GPIO<Port>:VOLTage..................................................... 1227
CONTrol<Ch>:SEQuence<Nr>:RFFE<Bus>:COMMand:DATA..........................................1227
CONTrol:VSE:ADDRess............................................................................................... 1228
CONTrol:VSE:CONFig:LOAD........................................................................................1228
CONTrol:VSE:CONFig:SAVE........................................................................................ 1228
CONTrol:VSE:CONNect............................................................................................... 1228
CONTrol:VSE:DISConnect............................................................................................1229
CONTrol:VSE:LOCal.................................................................................................... 1229
CONTrol:VSE:MODE....................................................................................................1229
CONTrol:VSE:TRACe...................................................................................................1229
SCPI command reference