Cisco Catalyst 3650 Series User Manual

Command History
ModificationRelease
This command was introduced.Cisco IOS XE 3.3SECisco IOS XE 3.3SE
Examples
This example shows how to display information about the redundancy facility:
Device# show redundancy
Redundant System Information :
------------------------------
Available system uptime = 6 days, 9 hours, 23 minutes
Switchovers system experienced = 0
Standby failures = 0
Last switchover reason = not known
Hardware Mode = Simplex
Configured Redundancy Mode = SSO
Operating Redundancy Mode = SSO
Maintenance Mode = Disabled
Communications = Down Reason: Simplex mode
Current Processor Information :
------------------------------
Active Location = slot 1
Current Software state = ACTIVE
Uptime in current state = 6 days, 9 hours, 23 minutes
Image Version = Cisco IOS Software, IOS-XE Software, Catalyst 3
850 L3 Switch Software (CAT3850-UNIVERSALK9-M), Version 03.08.59.EMD EARLY DEPLO
YMENT ENGINEERING NOVA_WEEKLY BUILD, synced to DSGS_PI2_POSTPC_FLO_DSBU7_NG3K_11
05
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Sun 16-S
Configuration register = 0x102
Peer (slot: 0) information is not available because it is in 'DISABLED' state
Device#
This example shows how to display redundancy facility client information:
Device# show redundancy clients
Group ID = 1
clientID = 20002 clientSeq = 4 EICORE HA Client
clientID = 24100 clientSeq = 5 WCM_CAPWAP
clientID = 24101 clientSeq = 6 WCM RRM HA
clientID = 24103 clientSeq = 8 WCM QOS HA
clientID = 24105 clientSeq = 10 WCM_MOBILITY
clientID = 24106 clientSeq = 11 WCM_DOT1X
clientID = 24107 clientSeq = 12 WCM_APFROGUE
clientID = 24110 clientSeq = 15 WCM_CIDS
clientID = 24111 clientSeq = 16 WCM_NETFLOW
clientID = 24112 clientSeq = 17 WCM_MCAST
clientID = 24120 clientSeq = 18 wcm_comet
clientID = 24001 clientSeq = 21 Table Manager Client
clientID = 20010 clientSeq = 24 SNMP SA HA Client
clientID = 20007 clientSeq = 27 Installer HA Client
clientID = 29 clientSeq = 60 Redundancy Mode RF
clientID = 139 clientSeq = 61 IfIndex
clientID = 3300 clientSeq = 62 Persistent Variable
clientID = 25 clientSeq = 68 CHKPT RF
clientID = 20005 clientSeq = 74 IIF-shim
clientID = 10001 clientSeq = 82 QEMU Platform RF
<output truncated>
The output displays the following information:
Command Reference, Cisco IOS XE Everest 16.5.1a (Catalyst 3650 Switches)
866
show redundancy

Cisco Catalyst 3650 Series Specifications

General

RAM	4 GB
Flash Memory	4 GB
Ports	24 or 48 10/100/1000 Ethernet ports
Uplinks	4 x 1G SFP or 4 x 10G SFP+ (depending on model)
Stacking	Up to 9 switches with StackWise-160
Layer Support	Layer 2, Layer 3
Software	Cisco IOS Software
Power Supply	Internal power supply; optional redundant power supply available
Storage Temperature	-40°F to 158°F (-40°C to 70°C)