Telit LE910 V2 Series AT Commands
80446ST10707A Rev. 0– 2015-11-03
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 10 of 509
Mod. 0808 2011-07 Rev.2
Band Selection - #BND ..................................................................................................................................... 250
Automatic Band Selection - #AUTOBND ......................................................................................................... 252
PPP-GPRS Connection Authentication Type - #GAUTH ................................................................................. 252
PPP-GPRS Parameters Configuration - # GPPPCFG ........................................................................................ 253
Skip Escape Sequence - #SKIPESC .................................................................................................................. 253
Subscriber number - #SNUM ............................................................................................................................ 255
SIM detection mode - #SIMDET ....................................................................................................................... 255
GSM Context Definition - #GSMCONT ........................................................................................................... 256
Show Address - #CGPADDR ............................................................................................................................ 257
Call Establishment Lock - #CESTHLCK .......................................................................................................... 258
Write to I2C - #I2CWR ..................................................................................................................................... 258
Read to I2C - #I2CRD ....................................................................................................................................... 259
Power Saving Mode Ring - #PSMRI ................................................................................................................. 260
Control Command Flow - #CFLO ..................................................................................................................... 261
Report concatenated SMS indexes - #CMGLCONCINDEX ............................................................................. 263
Codec Information - #CODECINFO ................................................................................................................. 264
Select language - #LANG .................................................................................................................................. 266
Enable RX Diversity and set DARP - #RXDIV ................................................................................................ 267
Set Encryption algorithm - #ENCALG .............................................................................................................. 267
Escape Sequence Guard Time - #E2ESC .......................................................................................................... 270
No Carrier Indication Handling - #NCIH .......................................................................................................... 271
Digital/Analog Converter Control - #DAC ........................................................................................................ 271
Change and insert file system password - #FILEPWD ...................................................................................... 272
User Determined User Busy - #UDUB .............................................................................................................. 273
HSDPA Channel Quality Inication - #CQI ........................................................................................................ 274
Ciphering Indication - #CIPHIND ..................................................................................................................... 274
CMUX Mode Set - #CMUXMODE .................................................................................................................. 275
Fast Dormancy - #FDOR ................................................................................................................................... 276
IMS PDP APN Name Set - #IMSPDPSET ........................................................................................................ 279
User Determined User Busy - #CREJ ................................................................................................................ 279
Reboot - #REBOOT .......................................................................................................................................... 279
4.1.6.2. Easy Scan® Extension AT Commands ..................................................................................................................... 280
Network Survey - #CSURV ................................................................................................................................ 280
Network Survey (Numeric Format) - #CSURVC ................................................................................................ 286
Network Survey Format - #CSURVF .................................................................................................................. 291
<CR><LF> Removing On Easy Scan® Commands - #CSURVNLF .................................................................. 291
Extended network survey - #CSURVEXT .......................................................................................................... 291
4.1.6.3. AT Run Commands .................................................................................................................................................. 292
Enable SMS Run AT Service - #SMSATRUN.................................................................................................... 292
Set SMS Run AT Service parameters - #SMSATRUNCFG ............................................................................... 294
SMS AT Run White List - #SMSATWL ............................................................................................................. 295
Set TCP Run AT Service parameter - #TCPATRUNCFG .................................................................................. 296
TCP Run AT Service in listen (server) mode - #TCPATRUNL .......................................................................... 298
TCP AT Run Firewall List - #TCPATRUNFRWL ............................................................................................. 299
TCP AT Run Authentication Parameters List - #TCPATRUNAUTH................................................................. 300
TCP AT Run in dial (client) mode - #TCPATRUND .......................................................................................... 301
Closing TCP Run AT Socket - #TCPATRUNCLOSE ........................................................................................ 302
TCP AT Run Command Sequence - #TCPATCMDSEQ .................................................................................. 302
TCP Run AT service to a serial port - #TCPATCONSER................................................................................. 302
Run AT command execution - #ATRUNDELAY ............................................................................................. 304
4.1.6.4. Consume commandsEvent Monitor Commands ....................................................................................................... 305
Configure consume parameters - #CONSUMECFG ........................................................................................... 305
Enable consume funztionality - #ENACONSUME ............................................................................................. 306
Report consume statistics - #STATSCONSUME ................................................................................................ 307
Block/unblock a type of service - #BLOCKCONSUME ..................................................................................... 309
#SGACT/#SSENDLINE configuration - #IPCONSUMECFG ........................................................................... 310
Open a connection, send data, close connection - #SSENDLINE ....................................................................... 311