Telit LE910 V2 Series AT Commands
80446ST10707A Rev. 0– 2015-11-03
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 11 of 509
Mod. 0808 2011-07 Rev.2
Circuit Switched Fallback - #CSFB ..................................................................................................................... 312
4.1.6.5. Event Monitor Commands ........................................................................................................................................ 313
Enable EvMoni Service - #ENAEVMONI .......................................................................................................... 313
EvMoni Service parameter - #ENAEVMONICFG ............................................................................................. 315
Event Monitoring - #EVMONI............................................................................................................................ 316
Send Message - #CMGS ...................................................................................................................................... 319
Write Message To Memory - #CMGW ............................................................................................................... 320
AT Command Delay - #ATDELAY .................................................................................................................... 322
4.1.6.6. Multisocket AT Commands ...................................................................................................................................... 323
Socket Status - #SS .............................................................................................................................................. 323
Socket Info - #SI .................................................................................................................................................. 325
Socket Type - #ST ............................................................................................................................................... 326
Context Activation - #SGACT ............................................................................................................................ 327
Socket Shutdown - #SH ....................................................................................................................................... 328
Socket Configuration - #SCFG ............................................................................................................................ 328
Socket Configuration Extended - #SCFGEXT .................................................................................................... 331
Socket configuration Extended 2 - #SCFGEXT2 ................................................................................................ 333
Socket configuration Extended 3 - #SCFGEXT3 ................................................................................................ 336
Socket Dial - #SD .............................................................................................................................................. 338
Socket Restore - #SO ......................................................................................................................................... 339
Socket Listen - #SL ........................................................................................................................................... 340
Socket Listen UDP - #SLUDP........................................................................................................................... 341
Socket Accept - #SA .......................................................................................................................................... 342
Socket Info Extended - #SIEXT ....................................................................................................................... 342
Detect the cause of a Socket disconnection - #SLASTCLOSURE .................................................................... 343
Receive Data In Command Mode - #SRECV .................................................................................................... 346
Send Data In Command Mode - #SSEND ......................................................................................................... 347
Send UDP data to a specific remote host - #SSENDUDP ................................................................................. 348
Send UDP data to a specific remote host extended #SSENDUDPEXT ............................................................. 350
Send data in Command Mode extended - #SSENDEXT ................................................................................... 351
IP Easy Authentication Type - #SGACTAUTH ................................................................................................ 352
Context activation and configuration - #SGACTCFG ....................................................................................... 352
Context activation and configuration extended - #SGACTCFGEXT ................................................................ 354
PAD command features - #PADCMD ............................................................................................................... 355
PAD forward character - #PADFWD ................................................................................................................ 355
Base64 encoding/decoding of socket sent/received data - #BASE64 ................................................................ 356
SSL Commands ................................................................................................................................................. 359
Open a socket SSL to a remote server - #SSLD ......................................................................................... 359
Enable a SSL socket - #SSLEN ................................................................................................................. 360
Close a SSL socket - #SSLH ..................................................................................................................... 362
Restore a SSL socket after a +++ - #SSLO ................................................................................................ 362
Read Data from a SSL socket - #SSLRECV .............................................................................................. 363
Report the status of a SSL socket - #SSLS ................................................................................................ 364
Manage the security data - #SSLSECDATA ............................................................................................. 365
Send data through a SSL socket - #SSLSEND .......................................................................................... 366
Send data through a secure sockect in Command Mode - #SSLSENDEXT .............................................. 367
Configure security parameters of a SSL socket - #SSLSECCFG ............................................................ 368
Configure additional parameters of a SSL socket - #SSLSECCFG2 ....................................................... 370
Configure general parameters of a SSL socket - #SSLCFG .................................................................... 370
Secure Socket Info - #SSLI ...................................................................................................................... 372
4.1.6.7. FTP AT Commands .................................................................................................................................................. 373
FTP Time-Out - #FTPTO .................................................................................................................................... 373
FTP Open - #FTPOPEN ...................................................................................................................................... 374
FTP Close - #FTPCLOSE ................................................................................................................................... 374
FTP Config - #FTPCFG ...................................................................................................................................... 374
FTP Put - #FTPPUT ............................................................................................................................................ 375
FTP Get - #FTPGET............................................................................................................................................ 377
To Next Page
Loading...
Need help?
General
